Others
|
| Problem |
|
|
|
|
|
| Cause and solution | |
|
|
|
|
|
|
|
|
| ||
Hot air is emitted from the air outlet grilles. | • This air comes out as a result of cooling the inside of the projector. This isn’t a product malfunction. | |||||||||
|
|
|
|
|
|
|
|
|
| |
No audio is output. |
|
|
|
|
|
| • Check that the volume isn’t set to low. | |||
|
|
|
|
|
|
|
|
| ||
Sound cannot be heard from the external audio out- |
| |||||||||
put (* Only applicable to the models which have the | • Check whether or not the volume is turned down. | |||||||||
external audio output.) |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| • The microcomputers inside the projector may be wrongly operating because of noise. | |
The menu can’t be used. |
|
|
|
|
|
| J Press the POWER button to turn off the lamp and unplug the power cord from the wall outlet. Wait about | |||
|
|
|
|
|
|
|
|
| 10 minutes, plug the power cord in, and try again. | |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| • Check that the battery is loaded in the remote control or the battery isn’t weak. (See page 8.) | |
The remote control doesn’t function easily or at all. | • Check that the remote control sensor isn’t exposed to direct sunlight or fluorescent light. (See page 8.) | |||||||||
• Use the remote control within its operation range. (See page 8.) | ||||||||||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| • Use the remote control at least 10 cm away from the projector. | |
|
|
|
|
|
|
|
|
| ||
The buttons on the control panel (except for the | • The password function is working. | |||||||||
POWER button) don’t function. |
|
|
|
|
|
| J Cancel the password lock. (See page 21.) | |||
|
|
|
|
|
|
|
|
|
| |
Abnormal sound is heard. |
|
|
|
|
|
| • Because the color wheel spins at a high speed, metallic sounds may be heard in rare occasions. Such symp- | |||
|
|
|
|
|
| tom is not a malfunction. | ||||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |
POWER | STATUS |
| ||||||||
|
|
|
|
|
|
|
|
| • 95% Lamp life exceed | |
|
|
|
|
|
|
|
|
| J Replace the lamp and reset the lamp hour. | |
Steady green | Blinking red | |||||||||
| ||||||||||
|
|
|
|
|
|
|
|
|
| |
ENGLISH
When the problems below occur after the lamp is replaced, check the following.
Problem |
| Cause and solution | |
|
| ||
The power isn’t turned on. | • Attach the lamp cover on the bottom correctly. | ||
• | Reset the lamp operation time. (See page 22.) | ||
| |||
|
|
| |
The STATUS indicator blinks. | • | Reset the lamp operation time. (See page 22.) | |
|
|
| |
Maintenance
Warning:
Do not use flammable solvents (benzene, thinner, etc.) and flammable aerosols when cleaning the projector body and lens. Flammable substances may ignite causing fire or breakdown while the lamp is illuminating.
Caution:
Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on the projector.
Cleaning of the projector and the ventilation slots
Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft cloth dampened with diluted mild detergent, and then wipe them with a dry cloth.
To protect the surface of the projector from fading or deteriorating:
•Do not spray insecticide on or inside the projector.
•Do not use benzine or thinner to clean it.
•Do not let rubber or plastic materials contact with projector.
Cleaning of the lens
Use a standard
