3-2

Amplifier Setup

To successfully setup the BLE100, you need to perform the following tasks:

ƒForward path alignment

ƒReturn path alignment

ƒCheck powering and surge protection options

Forward Path Alignment

You must perform the following BLE100 alignment procedures for proper performance in the forward path:

ƒSelect the appropriate cable equalizer or cable simulator

ƒSelect the appropriate input and midstage pads

ƒVerify proper flatness control

ƒVerify proper level control

Before You Begin

Before you begin to set-up the amplifier and perform forward-path alignment, please read the following instructions and recommendations.

For proper forward alignment obtain:

ƒRF output levels and tilts of all BLE100s in the forward or return path

ƒRF input level for the BLE100 being set up (from system design or as-built map)

ƒA carrier at the system’s highest frequency. It can be modulated or continuous wave (CW) and should be inserted in the headend at standard video levels. This carrier is used to simplify field set-up.

It is recommended that you:

ƒInstall the system design value SFE-100-* and a high value (20 dB or above) input pad

(JXP IN) before you install or remove the electronics chassis or apply power to the BLE100.

Leave the JXP IN pad location open if a high value pad is not available. A more accurate forward input test point reading is achieved with a high value pad installed.

ƒDo not remove the electronics chassis cover while the BLE100 is powered.

ƒDo not use wire jumpers to bypass the SFE-100-* location.

ƒRecognize that actual pad and SFE-100-* values may differ slightly from their design

values. This is caused by factors such as walkout errors, worst-case data utilization during design and temperature variation from 70°F.

ƒSecure the electronics chassis in the housing base and torque to 18-22 in-lbs. to facilitate heat transfer and avoid damage from overheating.

ƒIf the electronics chassis cover was removed for any reason, shut off the AC power before you reinstall the cover. Verify that all chassis cover screws are tightened to 10–12 in-lbs.

ƒPerform a bench alignment. Pre-aligning the BLE100 response on the bench (Section 4, “Bench Testing”) for a system signature simplifies field alignment.

BLE100 Installation and Operation Manual

Page 22 Page 24
Page 23
Image 23
Motorola BLE100 operation manual Forward Path Alignment, Before You Begin
Page 22 Page 24

BLE100 specifications

The Motorola BLE100 is an innovative device designed for efficiency and reliability in the realm of Bluetooth Low Energy (BLE) technology. As a compact and multifunctional solution, it caters to diverse applications, from cost-effective asset tracking to improving smart home environments. The BLE100 stands out for its practicality, making it ideal for both personal and commercial use.

One of the standout features of the Motorola BLE100 is its low power consumption. Leveraging Bluetooth Low Energy technology, the device can operate for extended periods without frequent battery replacements—ideal for remote monitoring applications where long-lasting performance is crucial. This characteristic ensures that users can rely on the BLE100 for day-to-day operations without the hassle of constant recharging.

In terms of connectivity, the BLE100 boasts seamless and stable connections over considerable distances. With a range of up to 100 meters in open environments, the device excels in maintaining reliable communication even in challenging conditions. Its compatibility with a wide array of Bluetooth-enabled devices ensures versatile usability, allowing users to integrate the BLE100 into existing systems with ease.

The Motorola BLE100 also prioritizes user-friendly design. The device is lightweight and compact, ensuring ease of installation and portability. Its robust build makes it resilient against environmental factors, while its sleek design enhances its aesthetic appeal. Moreover, straightforward setup processes and user interfaces facilitate quick deployment for various applications.

Another notable characteristic of the BLE100 is its advanced security features. With built-in encryption and pairing mechanisms, users can safeguard their data and communication. This is particularly vital in applications requiring confidential or sensitive information transfer.

The device supports various protocols and adheres to international standards, which ensures versatility and compatibility in multiple applications. Whether it's intelligent home systems seeking efficient device interaction or logistics needing simple asset tracking solutions, the Motorola BLE100 meets diverse needs.

In conclusion, the Motorola BLE100 is a powerful device that marries efficiency, functionality, and security. Its low power usage, reliable connectivity, user-friendly design, and robust features make it a top choice for anyone looking to enhance their Bluetooth Low Energy applications. With the BLE100, users can explore a wide range of possibilities, from smart technology integration to simplified monitoring solutions, all designed to optimize performance while maintaining a user-centric approach.
Top Page Image Contents