Section 5

Installation

The field installation procedures presented in the following subsections assume that the amplifier was previously tested and bench aligned. Cable power and RF signal must be available on the system. Although it is desirable to have a full complement of channels available for balancing, you can adjust the BLE100 adequately with a limited number of channels.

You can install the BLE-HSG/15 on a messenger strand (aerial) or in a pedestal. The following subsections provide details on each application.

Aerial Installation

The housing is normally mounted horizontally below the strand without the electronics chassis to avoid possible damage during installation. Connections are made using standard pin-type connectors with a nominal center-conductor diameter of 0.067 inches. The minimum length of the center-conductor pin is 1.35 inches and the maximum length is 1.5 inches. Longer pins can extend past the center-conductor seizure mechanism and degrade the match. Extremely long pins can result in a short circuit.

Figure 5-1

Center-conductor pin length

1.50” Max.

1.35” Min.

To install the unit:

1Power-down the cable before you install the housing. This avoids blown fuses, tripped circuit breakers, and possible personal injury.

2Mount the housing, and torque the two 5/16-inch messenger clamp bolts (illustrated in Figure 2-5) to 10 to 12 ft-lbs.

3Form the customary expansion loops and make all cable connections according to system design.

4Tighten the center-conductor seizure screw using a Phillips-head screwdriver. An alternate method is to use a 3/16-inch socket and a torque wrench. The recommended torque is

12 in-lbs. maximum.

5To avoid water ingress, ensure that aluminum connectors are torqued to the specifications recommended by the connector manufacturer.

6If previously removed, re-install the electronics chassis and fasten it to the housing with the four captive bolts. Torque to 18 to 22 in-lbs.

7Remove the input pad (JXP-IN) to avoid damage to the hybrids.

8Apply power to the unit and allocate a few minutes for warm up.

BLE100 Installation and Operation Manual

Page 40
Image 40
Motorola BLE100 operation manual Aerial Installation, Center-conductor pin length

BLE100 specifications

The Motorola BLE100 is an innovative device designed for efficiency and reliability in the realm of Bluetooth Low Energy (BLE) technology. As a compact and multifunctional solution, it caters to diverse applications, from cost-effective asset tracking to improving smart home environments. The BLE100 stands out for its practicality, making it ideal for both personal and commercial use.

One of the standout features of the Motorola BLE100 is its low power consumption. Leveraging Bluetooth Low Energy technology, the device can operate for extended periods without frequent battery replacements—ideal for remote monitoring applications where long-lasting performance is crucial. This characteristic ensures that users can rely on the BLE100 for day-to-day operations without the hassle of constant recharging.

In terms of connectivity, the BLE100 boasts seamless and stable connections over considerable distances. With a range of up to 100 meters in open environments, the device excels in maintaining reliable communication even in challenging conditions. Its compatibility with a wide array of Bluetooth-enabled devices ensures versatile usability, allowing users to integrate the BLE100 into existing systems with ease.

The Motorola BLE100 also prioritizes user-friendly design. The device is lightweight and compact, ensuring ease of installation and portability. Its robust build makes it resilient against environmental factors, while its sleek design enhances its aesthetic appeal. Moreover, straightforward setup processes and user interfaces facilitate quick deployment for various applications.

Another notable characteristic of the BLE100 is its advanced security features. With built-in encryption and pairing mechanisms, users can safeguard their data and communication. This is particularly vital in applications requiring confidential or sensitive information transfer.

The device supports various protocols and adheres to international standards, which ensures versatility and compatibility in multiple applications. Whether it's intelligent home systems seeking efficient device interaction or logistics needing simple asset tracking solutions, the Motorola BLE100 meets diverse needs.

In conclusion, the Motorola BLE100 is a powerful device that marries efficiency, functionality, and security. Its low power usage, reliable connectivity, user-friendly design, and robust features make it a top choice for anyone looking to enhance their Bluetooth Low Energy applications. With the BLE100, users can explore a wide range of possibilities, from smart technology integration to simplified monitoring solutions, all designed to optimize performance while maintaining a user-centric approach.