Installing the Optional CineWide Lens Mount | Vidikron Vision 110

Installation

6.Lock the lens in place by turning the Lens Locking Nut (to the left of the lens) 180 degrees counter-clockwise. (Use a 6.0mm hex wrench.)

7.Remove the Front Lens Cap.

8. Replace the Lens Cavity Front Cover.

9.Re-install the Projector Front Jewelry. Tighten the hex screws at the top and bottom of the jewelry to secure it.

3.5

Installing the Optional CineWide Lens Mount

If you are installing a standard (non-CineWide) Vision 110, skip this step and proceed with Mounting the Vision 110 (page 28).

If you are installing a Vision 110/CineWide, proceed with Installing the Fixed CineWide Base Plate (Vision 110/CineWide) (page 27).

If you are installing a Vision 110/CineWide with AutoScope, proceed as follows to install the AutoScope lens motor.

22	Vidikron Vision Model 110 Installation/Operation Manual

Image 36

Vidikron Vision 110 operation manual Installing the Optional CineWide Lens Mount

Contents

110 Page TWO Year Limited Warranty For Projectors, Video Processors and Controllers Effective Warranty Date Vidikron Important Safety Instructions Compliance Information Declaration of Conformity FCC Part 1Table of Contents Attach Lens Mounting Assembly to Lens Motor Carriage Plate Operation Maintenance and Troubleshooting Table of Contents Xii 1List of Figures List of Figures Xiv 1Introduction About This Manual Using This Manual If you need Turn to Description, Features and Benefits Vision 110 offers these key features and benefits Optional Accessories Controls and Functions Vision 110 at a Glance Vision 110 Rear Panel Vision 110 Rear Panel STAND-BY LED Vision 110 Rear Connector Panel Service only For future useRS-232/485 Control Port Volt 750 mA Trigger Outputs Hdmi I 1 / Hdmi II 2 Digital HD3 Input Vision 110 Remote Control Vision 110 Remote Control Picture Adjustment Buttons BRT Brightness On / OFFSource Selection Buttons VID S-Video Memory Preset Buttons Aspect Ratio Selection Buttons169 Lbox Letterbox 3Installation Remote ControlOperation Quick Setup Installation OverviewStep Procedure For Details, Refer to If installing a Vision 110/CineWide or Vision Installation Considerations Projector Installation OptionsInstallation Type Advantages Considerations Vision 110 Lens Options and Throw Ratios Ceiling Installation Floor InstallationVertical and Horizontal Position Horizontal Lens Shift Example only Vision 110 Vertical and Horizontal Lens Shift Limits Folded Optics Installing the Primary Projection Lens Disconnection or lens damage Installing the Optional CineWide Lens Mount 6shows the Vision 110/CineWide with AutoScope motor assembly Remove Vision 110 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 110/CineWide Adjusting the Projection Mounting the VisionFloor Mounting Upright Ceiling Mounting Inverted Angle Connecting Source Connections to the VisionHdmi Connections See Figure 110 11. Digital DTV RGB or Component Video Connections HD1, HD2 12. Digital DTV RGB or Component Video Connections HD3 DTV or Progressive Component YPbPr Source Analog Computer RGB Connections See Figure 13. Analog RGB Connections Video/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etc Connection 15. RS-232 Control System Connection Connecting 12-volt Trigger Outputs to External Equipment AutoScope Lens Motor RearRear Panel Connecting an External IR Power sourceReceiver to the Vision Rear Panel Turning on the Power Adjusting the Picture Orientation Primary Lens Adjustments FocusZoom Installing and Adjusting the CineWide Anamorphic Lens Primary lens is perfectly centered on the screen 19. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Using the On-Screen Menus 4Operation Memory Presets ServiceInput Source Aspect Ratio Main Menu Input SourceAspect Ratio Aspect Ratio Settings Description169 Hdtv programs in their native Picture Picture Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Memory Presets Memory PresetsInformation Information Calibration Calibration ISF NightISF Day OSD Position To adjust the menu and press Enter or Gain/Offset Refer to ISF Night Display Color, above Service ServiceHD Format Presets 5Maintenance and Troubleshooting Lamp Replacement Filter Replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port Configuration6Serial Communications Serial Commands and Responses Command Description ResponseInput Selection Commands Aspect Ratio Commands Command Description Response Image Preset Commands Menu Navigation CommandsPicture Adjust Commands Enter or Select button Serial Communications 7Specifications Vision 110 Specifications Home Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements Dimensions Vision 110 Dimensions Vision 110/CineWide with AutoScope Dimensions Supported Signal Timings by Input Supported Timings Format Resolution Frequency HD 1/HD 2/HD Specifications Page Vidikron