Manuals / MTD / Lawn and Garden / Lawn Mower

MTD 190-182,190-180 warranty Attaching The Blades, Inch Cutting Deck Models Only, Larger Blades

Models: 190-182,190-180

1 36

Download 36 pages 41.73 Kb

Page 9

Attaching The Blades

Smaller Blade

Part No. 742-0645

			Attaching The Blades
		NOTE: If your tractor is equipped with a 46” cutting deck,
		three 2-in-1 cutting blades are included with this kit. For
		improved bagging performance, install these blades on
		your tractor using the following instructions.
		Remove the blades from your tractor’s cutting deck as
		follows:
		1.	Remove the cutting deck from beneath the tractor,
		Larger Blades	(refer to Deck Removal in the MAINTENANCE
	Hex Flange Nut	Part No. 742-0644	section of your tractor’s operator’s manual for detailed
	Hex Flange Nut		instructions) then gently flip the deck over to expose
			instructions) then gently flip the deck over to expose
	Figure 5-1		its underside.
	Figure 5-1	2.	Place a block of wood between the center deck hous-
		2.	Place a block of wood between the center deck hous-
			ing baffle and the cutting blade to act as a stabilizer,
			keeping the blades from turning when you loosen the
			hex flange nuts.
		3.	Use a 15/16” wrench to remove the hex flange nut that
			secures the blade to the spindle assembly.

NOTE: The hex flange nut has a normal (right-handed)thread pattern. Do NOT attempt to force the nut in the incorrect direction. Doing so may damage the nut and create a safety hazard.

4.Install the new blades packed with the bagger. Be sure to install the blade with the side of the blade marked ‘‘Bottom’’ (or with a part number stamped in it) facing the ground when the rider is in the operating position.

5.Mount the SMALLER of the three blades to the CENTER spindle. The remaining two blades are interchangeable. See Fig. 5-1.

6.Use a torque wrench to tighten the blade spindle hex flange nut to between 70 and 90 foot-pounds.

7.Remount the cutting deck.

5

Attaching

The Blades

46-Inch Cutting

Deck Models Only

NOTE:

If your tractor is

equipped with a 46” cutting deck, three

2-in-1 cutting blades

are included with this kit. For proper bagging performance, install these blades on your tractor using the following instructions.

NOTE:

The hex flange nut has a normal (right- handed) thread pattern. Do NOT attempt to force the nut in the incorrect direction. Doing so may damage the nut and create a safety hazard.

Image 9

MTD 190-182,190-180 warranty Attaching The Blades, Inch Cutting Deck Models Only, Larger Blades, Hex Flange Nut

Contents

OPERATOR’S MANUAL ModelTo The Owner Carton Contents Assembly Parts Lists Warranty Twin Rear Bagger KitFinding and Recording Model Number TABLE OF CONTENTSCustomer Support BEFORE YOU START ASSEMBLING YOUR NEW EQUIPMENTDetermine The Model of Your Rider FastAttach Twin Bag Grass CollectorRider Model Identification Sample Model NumberCONTENTS OF CARTON Carton Contentstoll free at One Chute Tube# = Quantity CONTENTS OF HARDWARE PACKCarton Contents For decks with grass catcher pin not pre-installedAttaching The Bracket Assembly Attaching Bracket AssemblyModel Series Upper HoleAssembling Support Brackets Attaching Support Bracket Bracket AssemblyAttaching The Bracket Assembly Model SeriesAll Model Series Attaching Grass Bags Grass Bag CoverAttaching Grass Bags Grass Bag Cover port tube and opens46-Inch Cutting Deck Models Only Attaching The BladesAttaching The Blades Larger BladesAttaching Discharge Chute Attaching Discharge ChuteAll Model Series The retainer strap is fitted at position A on the discharge chuteAll Model Series Bagger UsageAttaching Discharge Chute Attaching Discharge ChuteFor Deck Part List Rear Twin BaggerFor parts and/or accessories please call Support Tube AssemblyMANUAL DEL OPERADOR ModelosIMPORTANTE Kit de embolsado posterior dobleBúsqueda y registro del número de modelo Asistencia al clienteANTES DE COMENZAR A MONTAR SU NUEVO EQUIPO Colector de césped FastAttach con sistema de bolsa doble Identificación del modelo de podadora tractorDetermine el modelo de la podadora tractor FiguraCONTENIDO DE CARTÓN Contenido de la cajaSi le faltan piezas la unidad. LlameNOTA CONTENIDO DE PAQUETE DE HARDWAREContenido de la caja Si le faltan piezasInstalación Conjunto de soporte Instalación Conjunto de soporteModelos series Placa de enganche Figura Orificio superior FiguraInstalación del soporte y del conjunto del soporteEnsamblado de los soportes Instalación del conjunto del soportebolsas Instalaciónde las bolsas para césped y de la cubierta para las series 600 a inclusive¡Modelos equipados con Instalación de las cuchillasSólo una 46” CubiertaInstalación del canal de descarga Instalación del canal de descargaEn tractores de modelos más antiguos FiguraTodas las series de modelos Uso de la embolsadoramodelos 600 a Instalación del canal de descargaMANUEL DE L’OPÉRATEUR Modèle 190-180Collecteur arrière à deux sacs MTD LLC, P.O. BOX 361131 CLEVELAND, OHIOSupport client Pour trouver et enregistrer le numéro de modèleTABLE DES MATIERES AVANT D’ASSEMBLER VOTRE NOUVEL ÉQUIPEMENTdu modèle du tracteur IdentificationCollecteur d’herbe à deux sacs FastAttach Déterminer le modèle de votre tracteurCONTENU DU CARTON Contenu du cartonSi des pièces sont manquantes, ne contactez pas votre revendeur, mais appelez directement MTD auREMARQUE PIÈCES DE QUINCAILLERIEContenu du carton Si des pièces sont manquantes, ne contactez pas votre revendeur, maisMontage du support de fixation Montage du support de fixationModèles de série Modèles de sériepalier sup- port et du support de fixation Montage duMontage des paliers supports Modèle de la sérieMontage des sacs à herbe et du couvercle vercleMontage des sacs à herbe et du cou Toute la Série ModèleLe fait d’Attacher les Lames Le fait d’Attacher les LamesNOTEZ Sur les Modèles Équipés avec 46” Pont Seulementla goulotte d’éjection Montage deMontage de la goulotte d’éjection Toute la Série ModèleTous les modèles Utilisation du collecteurMontage de la goulotte d’éjectionMTD LLC, P.O. BOX 361131 CLEVELAND, OHIO