S95 Extended Result Codes Control | Multi-Tech Systems MT2456SMI22

Chapter 4 - V.22bis Commands

S91 – PSTN Transmit Attenuation Level

S91 sets transmit attenuation level from 0 to 15 dBm for the PSTN mode, resulting in a transmit level from 0 to -15 dBm.

Range: 0 to 15 dBm (Corresponding to 0 to -15 dBm transmit level.)

Default: 10 (-10 dBm transmit level.)

S95 - Extended Result Codes Control

A bit set to a 1 in this parameter, in conjunction with the W command, will enable the corresponding extended result code.

The W command determines the corresponding actual result code reporting (see W command). Default: 0

Bit 0 CONNECT result code indicates DCE speed instead of DTE speed.

Bit 1 Append/ARQ to CONNECT XXXX result code in error-correction mode (XXXX = rate). Bit 2-7 Reserved.

Multi-Tech Systems, Inc. MT2456SMI-22 SocketModem Developer’s Guide

Page 44

Image 44

Multi-Tech Systems MT2456SMI22 manual S91 Pstn Transmit Attenuation Level, S95 Extended Result Codes Control

Contents

SocketModem PN S000281A, Version a Country By Email By Phone Contents Product Description Specifications Product Description Technical Specifications Speed Conversion Physical Dimensions Maximum Component Height Pin Configurations Pin Descriptions 3V DC Power Handling Precautions 3V and 5V Serial SocketModemInput High Input Low Outputs Output High Output Low Generic Modem Control Commands DTE/DCE CommandsCall Control Commands Modulation Control Commands Error Control and Data Compression Commands Synchronous Access Mode CommandsFast Connect Command Line Side Device Commands 22bis Generic Modem Control Commands Soft Reset and Restore ProfileOperating Mode +VCID Caller ID CID +GCI Country of Installation Identification Restore Factory Configuration Profile ProcedureLocal Analog Loopback Test Load to Internal RAM 22bis DTE/DCE-Modem Interface commands Command EchoQuiet Result Codes Control Result Code Form Connect Ring No Carrier Error No Dial Tone Busy No Answer Extended Result Codes Short Form Long Form Value in ATXn Command Rlsd OptionResult Codes OK 0 or DTR Option +IFC DTE-Modem Local Flow Control RTS/CTS Option\G Modem-to-Modem Flow Control XON/XOFF EM Shielding Data +IBC In Band CommandsEntering and Exiting In Band Active State Band Processing of AT Commands Command Hex Codes Description Supported DTE-to-DCE CommandsSupported DCE-to-DTE Commands Dial Modifiers 22bis Call Control CommandsDial Set Tone Dial Default Result Code Set Pulse Dial DefaultReturn to On-Line Data Mode Speaker Volume Display Current Configuration and Stored Profiles MSpeaker ControlSelect Guard Tone Select Pulse Dial Make/Break Ratio \V Single Line Connect Message Enable Report Line Signal LevelReport Line Signal Quality Display Blacklisted Numbers Display Delayed Numbers NO. Phone Number -DELAYBehavior in Data Mode Syntax *D Example +VDR Distinctive Ring +PCW Call Waiting EnableReporting Selected Values 22bis Modulation Control Commands Table of +MS Command Supported Rates+MS Modulation Selection Syntax Enable/Disable Line Quality Monitor and Auto-Retrain ITU-T or Bell 22bis Error Control and Data Compression Commands +ESR Selective Repeat+ETBM Call Termination Buffer Management \B Transmit Break to Remote Result Codes OK 0 to 5 Error Otherwise Break Control 22bis Synchronous Access Mode Commands +ESA Configure Synchronous Access SubmodeReporting Selected Options +ESA? Transmit Flow Control Thresholds +ITF? Syntax $Fn Defined Values 22bis FastConnect Command$F Fast Connect Control 22bis Line Side Device Commands Threshold Adjustments for Telephony ExtensionTRV Tip and Ring Voltage Measurement Response 22bis S-Parameters Read/Write S-Parameter Ascii Summary of S-Parameter DefaultsRegister Function Range/Units Default S0 Number of Rings to Auto-Answer S1 Ring CounterS2 Escape Character S3 Carriage Return Character S8 Pause Time For Dial Delay S10 Lost Carrier To Hang Up DelayS12 Escape Prompt Delay EPD S9 Carrier Detect Response Time S16 Test Mode Bit Mapped Options Status S19 ReservedS20 Reserved S21 V.24/General Bit Mapped Options Status S24 Sleep Inactivity Timer S25 Delay To DTR OffS26 RTS to CTS Delay S22 Speaker/Results Bit Mapped Options Status S30 Disconnect Inactivity Timer S27 Bit Mapped Options StatusS28 Bit Mapped Options Status S29 Flash Dial Modifier Time S38 Delay Before Forced Hang Up S36 Lapm Failure ControlS37 Desired Line Connection Speed S39 Flow Control Bit Mapped Options Status S41 General Bit Mapped Options Status S48 V.42 Negotiation ActionS82 Break Handling Options S86 Call Failure Reason Code S91 Pstn Transmit Attenuation Level S95 Extended Result Codes Control 22bis Result Codes Table of Result Code DefinitionsCode Message Meaning Connect 75TX/1200RX Is enabled Block Diagram Figure A-1. Serial Test/Demo Board Block Diagram Product Safety and EMC Approvals Country CertificationsCountry Country Code More planned Regulatory Design Considerations Hardware Considerations Safety SocketModem Placement Qty Name Description Telecom Requirements for the United States ComplianceMulti-Tech Systems, Inc. Compliance Label Content and Format Label Physical Characteristics Other Label Requirements Telecommunications Regulations for CanadaLabeling Continuity and Changes New Zealand Telecom Warning Notice Industry Canada South African Statement EMC, Safety, and R&TTE Directive ComplianceInternational Modem Restrictions Index Index