Index

Index

$F – FastConnect Control, 33 %L - Report Line Signal Level, 24 %Q - Report Line Signal Quality, 24 &C - RLSD Option, 17

&D - DTR Option, 17

&F - Restore Factory Configuration (Profile), 14 &G - Select Guard Tone, 23

&K - Flow Control, 17

&P - Select Pulse Dial Make/Break Ratio, 23 &R - RTS/CTS Option, 18

&T - Local Analog Loopback Test, 14

&V - Display Current Configuration and Stored Profiles, 23

** - Load to Internal RA, 14

*B - Display Blacklisted Numbers, 24, 25

+ESA - Configure Synchronous Access Submode, 31 +ESR - Selective Repeat, 29

+GCI - Country of Installation, 13

+IBC – In Band Commands, 19

+IFC - DTE-Modem Local Flow Control, 18 +MS - Modulation Selection, 27

+PCW - Call Waiting Enable, 26 +VCID - Caller ID (CID), 12 +VDR - Distinctive Ring, 26

+VRID - Report Retrieved Caller ID (CID), 12

A- Answer, 22

B- ITU-T or Bell, 28

B - Transmit Break to Remote, 29 Country Certifications, 48

D - Dial, 21

Design considerations Vendor recommendations, 49

E - Command Echo, 15 Electrical Characteristics, 9

EMC, Safety, and R&TTE Directive Compliance, 56 FCC Regulations, 52

G - Modem-to-Modem Flow Control (XON/XOFF), 18

H- Disconnect (Hang-Up), 22 Handling Precautions, 9

I- Identification, 13

International Modem Restrictions, 56

K - Break Control, 30

L - Speaker Volume, 22

Mechanical Specifications, 6

Multi-Tech Systems, Inc. Compliance, 52

N - Operating Mode, 12

New Zealand Telecom Warning Notice, 55

O- Return to On-Line Data Mode, 22

P- Set Pulse Dial Default, 22 Physical Dimensions, 6

Pin Configurations, 7 Placement, SocketModem, 51 Product Approvals, 48 Safety considerations, 50

Serial Demo Board block diagram, 47 South African Statement, Regulations, 56

Specifications,Mechanical, 6

Specifications,Technical, 5

–STE= - Set Telephony Extension, 25 T - Set Tone Dial Default, 22 Table of Result Codes, 16 Technical Specifications, 5

-TRV – Tip and Ring Voltage Measurement, 34

-TTE - Threshold Adjustments for Telephony Extension, 34

V.22bis Commands

$F – FastConnect Control, 33 %L - Report Line Signal Level, 24 %Q - Report Line Signal Quality, 24 &C - RLSD Option, 17

&D - DTR Option, 17

&F - Restore Factory Configuration (Profile), 14 &G - Select Guard Tone, 23

&K - Flow Control, 17

&P - Select Pulse Dial Make/Break Ratio, 23 &R - RTS/CTS Option, 18

&T - Local Analog Loopback Test, 14

&V - Display Current Configuration and Stored Profiles, 23

** - Load to Internal RA, 14

*B - Display Blacklisted Numbers, 24, 25

+ESA - Configure Synchronous Access Submode, 31 +ESR - Selective Repeat, 29

+ETBM - Call Termination Buffer Management, 29 +GCI - Country of Installation, 13

+IBC – In Band Commands, 19

+IFC - DTE-Modem Local Flow Control, 18 +MS - Modulation Selection, 27

+PCW - Call Waiting Enable, 26 +VCID - Caller ID (CID), 12 +VDR - Distinctive Ring, 26

+VRID - Report Retrieved Caller ID (CID), 12

A- Answer, 22

B- ITU-T or Bell, 28

\B - Transmit Break to Remote, 29 Call Control Commands, 21

D- Dial, 21

E- Command Echo, 15 FastConnect Command, 33

\G - Modem-to-Modem Flow Control (XON/XOFF), 18 Generic Modem Control, 12

H- Disconnect (Hang-Up), 22

I- Identification, 13 \K - Break Control, 30

L- Speaker Volume, 22

Line Side Device Commands, 34

M- Speaker Control, 23 Modulation Control Commands, 27 \N - Operating Mode, 12

O- Return to On-Line Data Mode, 22

P- Set Pulse Dial Default, 22

Q- Quiet Results Codes Control, 15

Multi-Tech Systems, Inc. MT2456SMI-22 SocketModem Developer’s Guide

57

Page 57
Image 57
Multi-Tech Systems MT2456SMI22 manual Index