Safety | Multi-Tech Systems MT2456SMI22 manual

Appendix B – Product Approvals, Regulatory Design Considerations, Compliance

Recommended Ferrite (SMT)

Manufacturer – Associated Component Technology (ACT) – Part # - YCB-1206

Manufacturer – Murata Erie – Part # - BLM31A601SPT

Recommended Ferrite (Thru-Hole)

Manufacturer – Associated Component Technology (ACT) – Part # - WB2-2.OT

Recommended Capacitor

Manufacturer – Murata Erie – Part # - GHM3045X7R221K-GC (Surface mount device) and Part # - DE0807B221K-KH (Thru-hole device)

Manufacturer – Ever Grace Electronic Industrials -- Part # - YP221K2EA7PS Note: The capacitors used on T&R must have a Y2 safety rating.

Recommended Connector

Manufacturer – Stewart – Part # - SS-6446-NF-A431

Recommended Fuse

Manufacturer – RayChem – Part # - TR600-150

Note: The fuse is also needed to meet UL1950 3rd edition protection against over-voltage from power line crosses.

Common Mode Choke

Manufacturer – TDK – Part # - ZJYS51R5-2PT

Recommended Sidactor

Manufacturer – Teccor Electronics – Part # - P#3100SA

Manufacturer – ST Microelectronics -- Part 1 – SMP100-270

Recommended Transceiver

Manufacturer – Analog Devices – Part # - ADM207EAR

Safety

All creepages and clearances for the MT2456SMI have been designed to meet requirements of safety standards EN 60950. The requirements are based on a working voltage of 250V. When the recommended DAA circuit interface is implemented in a third party design all creepage and clearance requirements must be strictly adhered to. The third party safety design must be evaluated by the appropriate national agency per the required specification.

User accessible areas: Based on where the third party design is to be marketed/sold or used, it may be necessary to provide an insulating cover over all TNV exposed areas. Consult with the recognized safety agency to determine the requirements.

Notice: Even if the recommended design considerations are followed, there are no guarantees that a particular system will comply with all the necessary regulatory requirements. It is imperative that specific designs be completely evaluated by a qualified/recognized agency.

Multi-Tech Systems, Inc. MT2456SMI-22 SocketModem Developer’s Guide

50

Image 50

Multi-Tech Systems MT2456SMI22 manual Safety

Contents

SocketModem PN S000281A, Version a Country By Email By Phone Contents Product Description Specifications Product Description Technical Specifications Speed Conversion Physical Dimensions Maximum Component Height Pin Configurations Pin Descriptions 3V DC Power Input High Input Low Handling Precautions3V and 5V Serial SocketModem Outputs Output High Output Low Call Control Commands Generic Modem Control CommandsDTE/DCE Commands Modulation Control Commands Fast Connect Command Error Control and Data Compression CommandsSynchronous Access Mode Commands Line Side Device Commands Operating Mode 22bis Generic Modem Control CommandsSoft Reset and Restore Profile +VCID Caller ID CID +GCI Country of Installation Identification Local Analog Loopback Test Restore Factory Configuration ProfileProcedure Load to Internal RAM Quiet Result Codes Control 22bis DTE/DCE-Modem Interface commandsCommand Echo Result Code Form Connect Ring No Carrier Error No Dial Tone Busy No Answer Extended Result Codes Result Codes OK 0 or Short Form Long Form Value in ATXn CommandRlsd Option DTR Option +IFC DTE-Modem Local Flow Control RTS/CTS Option\G Modem-to-Modem Flow Control XON/XOFF EM Shielding Data +IBC In Band CommandsEntering and Exiting In Band Active State Band Processing of AT Commands Command Hex Codes Description Supported DTE-to-DCE CommandsSupported DCE-to-DTE Commands Dial Modifiers 22bis Call Control CommandsDial Return to On-Line Data Mode Set Tone Dial DefaultResult Code Set Pulse Dial Default Speaker Volume Select Guard Tone Display Current Configuration and Stored ProfilesMSpeaker Control Select Pulse Dial Make/Break Ratio Report Line Signal Quality \V Single Line Connect Message EnableReport Line Signal Level Display Blacklisted Numbers Behavior in Data Mode Display Delayed NumbersNO. Phone Number -DELAY Syntax *D Example +VDR Distinctive Ring +PCW Call Waiting EnableReporting Selected Values +MS Modulation Selection 22bis Modulation Control CommandsTable of +MS Command Supported Rates Syntax Enable/Disable Line Quality Monitor and Auto-Retrain ITU-T or Bell +ETBM Call Termination Buffer Management 22bis Error Control and Data Compression Commands+ESR Selective Repeat \B Transmit Break to Remote Result Codes OK 0 to 5 Error Otherwise Break Control Reporting Selected Options 22bis Synchronous Access Mode Commands+ESA Configure Synchronous Access Submode +ESA? Transmit Flow Control Thresholds +ITF? Syntax $Fn Defined Values 22bis FastConnect Command$F Fast Connect Control TRV Tip and Ring Voltage Measurement 22bis Line Side Device CommandsThreshold Adjustments for Telephony Extension Response 22bis S-Parameters Read/Write S-Parameter Ascii Summary of S-Parameter DefaultsRegister Function Range/Units Default S2 Escape Character S0 Number of Rings to Auto-AnswerS1 Ring Counter S3 Carriage Return Character S12 Escape Prompt Delay EPD S8 Pause Time For Dial DelayS10 Lost Carrier To Hang Up Delay S9 Carrier Detect Response Time S20 Reserved S16 Test Mode Bit Mapped Options StatusS19 Reserved S21 V.24/General Bit Mapped Options Status S26 RTS to CTS Delay S24 Sleep Inactivity TimerS25 Delay To DTR Off S22 Speaker/Results Bit Mapped Options Status S28 Bit Mapped Options Status S30 Disconnect Inactivity TimerS27 Bit Mapped Options Status S29 Flash Dial Modifier Time S37 Desired Line Connection Speed S38 Delay Before Forced Hang UpS36 Lapm Failure Control S39 Flow Control Bit Mapped Options Status S82 Break Handling Options S41 General Bit Mapped Options StatusS48 V.42 Negotiation Action S86 Call Failure Reason Code S91 Pstn Transmit Attenuation Level S95 Extended Result Codes Control Code Message Meaning 22bis Result CodesTable of Result Code Definitions Connect 75TX/1200RX Is enabled Block Diagram Figure A-1. Serial Test/Demo Board Block Diagram Country Country Code Product Safety and EMC ApprovalsCountry Certifications More planned Regulatory Design Considerations Hardware Considerations Safety SocketModem Placement Qty Name Description Telecom Requirements for the United States ComplianceMulti-Tech Systems, Inc. Compliance Label Content and Format Label Physical Characteristics Other Label Requirements Telecommunications Regulations for CanadaLabeling Continuity and Changes New Zealand Telecom Warning Notice Industry Canada South African Statement EMC, Safety, and R&TTE Directive ComplianceInternational Modem Restrictions Index Index