OPERATION

CLEAR A CLOGGED DISCHARGE CHUTE

DANGER: Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never clear or unclog discharge chute with your hands, or while engine is running. Fingers can quickly become caught and traumatic amputation or severe laceration can result.

SHUT OFF THE ENGINE!

Wait 10 seconds to be sure that the impeller blades have stopped rotating.

Always use a clean-out tool, not your hands.

A clean-out tool (A, Figure 13) is attached to either the handle or the top of the auger housing. Use the clean-out tool to remove snow from the auger housing.

A

Clean-Out Tool

Figure 13

OPERATING TIPS

1.Most efficient snowthrowing is accomplished when snow is removed immediately after it falls.

2.For complete snow removal, slightly overlap each swath previously taken.

3.Snow should be discharged downwind whenever possible.

4.For normal usage, set the skids 1/8 inch (3 mm) below the scraper bar. For extremely hard-packed snow surfaces, the skids may be ad- justed upward to ensure cleaning efficiency.

5.On gravel or crushed rock surfaces, the skids should be set at 1-1/4 inch (32 mm) below the scraper bar (see “Adjust Skid Height” in the MAINTENANCE section of this manual). Rocks and gravel must not be picked up and thrown by the machine.

6.After the snowthrowing job has been completed, allow the engine to idle for a few minutes, to melt snow and ice accumulated on the engine.

7.Clean the snow thrower thoroughly after each use.

8.Remove ice and snow accumulation and all debris from the entire snow thrower, and flush with water (if possible) to remove all salt or other chemicals. Wipe snow thrower dry.

9.Before starting snow thrower, always inspect augers and impeller for ice accumulation and/or debris, which could result in snow thrower damage.

10.Check oil level before every start. Make sure the oil is at the FULL mark on the oil fill cap/dipstick.

17

Page 17
Image 17
Murray 1737920, 1695722 manual Clear a Clogged Discharge Chute, Operating Tips

1737920, 1695722 specifications

Murray 1737920 and 1695722 represent two significant advancements in the realm of smart technology, particularly in the area of home automation and energy management. These devices integrate cutting-edge features designed to enhance user experience while optimizing energy efficiency.

One of the main characteristics of Murray 1737920 is its intelligent energy management system, which utilizes real-time data analytics to monitor energy consumption patterns. The device employs machine learning algorithms to intelligently predict energy requirements, allowing users to reduce waste and lower their utility bills. Additionally, it has a user-friendly interface that provides insights into energy usage, enabling homeowners to make informed decisions about their consumption.

Murray 1695722, on the other hand, focuses more on home automation and security. With built-in Wi-Fi connectivity, it allows users to control various appliances remotely through a dedicated mobile application. This feature not only enhances convenience but also allows for enhanced security by enabling users to monitor their homes in real-time. The device is equipped with motion sensors and alert systems that can notify homeowners of any unusual activity, adding an extra layer of protection.

Both devices integrate seamlessly with existing smart home ecosystems, supporting popular communication protocols such as Zigbee and Z-Wave. This compatibility allows users to expand their systems by adding other smart devices, creating a fully integrated home automation experience.

In terms of installation, both Murray models are designed to be user-friendly. They typically come with comprehensive instructions, and many features can be accessed with minimal technical knowledge. The focus on ease of use extends to their maintenance, with straightforward troubleshooting and support available through the manufacturers.

Another important feature of both devices is their commitment to sustainability. By helping families monitor and manage their energy consumption, they play a crucial role in promoting more eco-friendly practices within households. Combined, Murray 1737920 and 1695722 stand out as leaders in smart home technology, emphasizing efficiency, security, and user-centric design principles that cater to the evolving needs of modern homeowners. These innovations represent a significant step forward in creating energy-conscious and secure living environments.