Manuals / N-Tron / Computer Equipment / Switch

N-Tron 608MFXE-ST-80, 608MFX-ST, 604MFX-ST Replacing the Standby Master during operation, 12/15/05

Models: 608MFXE-ST-80 608MFX-ST 608MFXE-ST-40 604MFX-ST 604MFXE-ST-40 608MFXE-ST-15 604MFXE-ST-15 604MFXE-ST-80

1 22

Page 11

Replacing the Standby Master during operation

FIBER OPTIC PAIR	#7	608MFX
FIBER OPTIC PAIR	#7	RING


		MANAGER

608M FX	#7		#8			608M FX
608M FX	#7		FIBER OPTIC PAIR			Standby
						Standby
						M as te r
				Cat5E		#1
				Cat5E		#1
				#8
608M FX		#7	FIBER OPTIC PAIR	#8		608M FX
608M FX		#7	FIBER OPTIC PAIR			608M FX

					#1
					#1

FIBER OPTIC PAIR	#7	608MFX
FIBER OPTIC PAIR	#7	RING


		MANAGER

	ITP Cable
					#7
					#7

#7	FIBER OPTIC PAIR	#8		608M FX
#7		#8		Standby


				Slave
		Cat5E		#1
		Cat5E		#1
#7		#8
#7	FIBER OPTIC PAIR	#8		608M FX
	FIBER OPTIC PAIR			608M FX

			#1	#7
			#1

608MFX Network Segment Redundancy

Figure 2

Replacing the Standby Master during operation

When replacing a standby master during operation, the following procedure is necessary to prevent an interruption on the network.

1.Remove the terminal block for power supply to the standby master.

2.Remove the signal lines and the standby connecting cable from the standby master.

3.Connect the signal lines to the replacement device.

4.Plug the power terminal block into the replacement device.

When replacing the standby slave, no special steps are necessary.

12/15/05

Page 11

Image 11

N-Tron 608MFXE-ST-80, 608MFX-ST, 604MFX-ST, 608MFXE-ST-40 manual Replacing the Standby Master during operation, 12/15/05

Contents

Hardware Installation Guide 600 Series Industrial Ethernet Switches12/15/05 12/15/05 Industrial Ethernet Switch Installation GuideCopyright, N-TRON Corp 820 S. University Blvd., Suite 4E 12/15/0512/15/05 ELECTRICAL SAFETYLASER SAFETY 604/608MFXE Version Only Safety Warnings12/15/05 600 Series Industrial Ethernet SwitchKey Features 12/15/05 PACKAGE CONTENTSINSTALLATION UNPACKING19” Rack Mounting 600 Series Hazardous Location Installation RequirementsPersonnel Qualification Requirements DIN-Rail Mounting12/15/05 APPLYING POWER12/15/05 CONNECTING THE STANDARD RINGSimultaneous Standby and Redundancy Manager Operation CONNECTING MULTIPLE RINGS 608MFX Onlycannot be used as Ring Couplers Port Assignment in the Standby Mode12/15/05 Replacing the Standby Master during operation12/15/05 DISPLAYS AND OPERATING CONTROLS LED’s Fault red LED12/15/05 Port LED’s12/15/05 “Select/Set” ButtonIEEE 802.1P, QOS Two-Pin Dip Switch SettingAging Time IEEE 802.1Q, VLANPin DSR Pin RXD Pin RTS Pin TXD Pin CTS Pin DTR Pin Pin GND Pin Serial InterfaceStandby-Sync Port 608MFX Only 12/15/0512/15/05 Serial CableHyperterminal 12/15/05 TROUBLESHOOTINGFCC STATEMENT 12/15/05 Fiber Transceiver Characteristics multimode/single mode - 15kmKEY SPECIFICATIONS Recommended Wiring ClearanceDescription Key Specifications Cont Emissions and Safety ApprovalsWarranty Ordering Information12/15/05 N-TRON Limited Warranty12/15/05 AND NON-INFRINGEMENT, ALL OF WHICH ARE EXPRESSLY DISCLAIMED. N-TRON NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. N-TRON SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT OR MALFUNCTION IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMERS OR ANY THIRD PERSONS MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO OPEN, REPAIR OR MODIFY THE PRODUCT, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, POWER CUTS OR OUTAGES, OTHER HAZARDS, OR ACTS OF GOD