Manuals / NEC / Computer Equipment / Printer Accessories

NEC ISDN-PRI manual DIL/IRG No Answer Destination, Day/Night Mode Incoming Group Number Default

Models: ISDN-PRI

1 134

Download 134 pages 16.04 Kb

Page 117

Program 22 : Incoming Call Setup

22-08 : DIL/IRG No Answer Destination

22-08 : DIL/IRG No Answer Destination

Level:

IN

Aspire S	Aspire

• Available.	• Available.

Description

For DIL Delayed Ringing, use Program 22-08 : DIL/IRG No Answer Destination to assign the DIL No Answer Ring Group. An unanswered DIL rings this group after the DIL No Answer Time expires (Program 22-01-04). DIL Delayed Ringing can also reroute outside calls ringing a Ring Group.

You make eight assignments, one for each Night Service mode.

Input Data

Trunk Port Number

001-200

Day/Night Mode		Incoming Group Number	Default

1-8	0 (No setting)		1
	1-100 (Incoming Group)
	102	(In-Skin/External Voice Mail)
	103	(Centralized Voice Mail)

Conditions

None

Feature Cross Reference

●Direct Inward Line (DIL)

●Ring Group

Aspire ISDN PRI Manual

◆ 111

Image 117

NEC ISDN-PRI manual DIL/IRG No Answer Destination, Day/Night Mode Incoming Group Number Default

Contents

Aspire Page Table of Contents Ii Table of Contents Program 15 Extension, Basic SetupProgram 35 Smdr Options Iv Table of Contents Section Isdn PRI FeaturesSection About Isdn Introduction to IsdnIntroduction to Isdn Primary Rate Interface PRI Installation Isdn FeaturesInstalling the Aspire T1/PRI Interface PCB P/N DescriptionSwitch Name T1/PRI Interface PCB SwitchesResult Pin No Connection RJ45 Cable Connector CN3 Bus ConnectionTo install a T1/PRI Interface PCB RxD data R RxD data T TxD data R1 TxD data T1 No connection For Your Notes Primary Rate Interface PRI, Answering Calls How the Telco Handles PRI Trunks Default SettingHow the Telephone System Handles PRI Trunks Trunk Trunk Channel Number Group NumberProgramming Signal detection limitOn next Programming Cont’dAspire Software Manual for did programming Telephones? PCB Setup Logical Port Number PCB Setup Isdn Line ModePCB Setup CRC Multi-Frame CRC4 PCB Setup Layer 3 Timer TypePCB Setup Short/Long Haul PCB Setup Networking System NumberPCB Setup Loss-of-Signal Detection Limit PCB Setup Service Protocol for S-PointRing Cycle Setup Normal Incoming Call on Trunk Trunk Access Map for ExtensionsSystem options for Caller ID Wait Facility IE Timer System Options for Incoming Calls Ring No Answer Alarm TimeNormal Incoming Ring Mode Incoming Call Trunk SetupTrunk Ring Tone Range Incoming Extension Ring Group AssignmentOperation Related FeaturesFor Your Notes Description Primary Rate Interface PRI, Placing CallsProgramming Stop 15-01-04, enter Should Caller ID be included Yes Access or trunk group 14-01-02 transmit PCB Setup Clip Information PCB Setup Isdn Line ModeBasic Trunk Port Setup Outgoing Calls Trunk Access Code Alternate Trunk Route Access CodeBasic Trunk Data Setup Dtmf Tones for Outgoing Calls Basic Extension Data Setup Isdn Caller IDClass of Service Options Outgoing Call Service Isdn Clip Class of Service for ExtensionsClass of Service Options Isdn Connected Line Identiﬁcation Repeat Dial Setup Time for Send Busy Tone for Isdn TrunkIsdn Calling Party Number Setup for Extensions Isdn Calling Party Number Setup for TrunksCoiu Initial Data Setup Individual Trunk Group Route for ExtensionsRepeat Redial HandsfreeTo place a call over a speciﬁc PRI trunk Operation Cont’dIsdn PRI Programming Section Isdn PRI ProgrammingSection Programming How to Use This SectionBefore You Start Programming Before Reading This SectionHow to Exit the Programming Mode How to Enter the Programming ModeTo enter the programming mode Password User Name Level Programs at this LevelUsing Keys to Move Around in the Programs When you want toKeys for Entering Data With Software Prior to Programming Names and Text MessagesWith Software 2.05+ Use this keypad When you want to DigitWhat the Soft Key Display Prompts Mean Using Soft Keys For ProgrammingPCB Setup Program 10 System Conﬁguration SetupFor Priu Unit Input Data Default Clip InformationInput Data Default Feature Cross ReferenceTelephone Programming Instructions To enter data for Program 10-03 PCB SetupDescription Pre-Ringing Setup← −1 +1 → To enter data for Program 10-08 Pre-Ringing SetupFor Your Notes Program 11 System Numbering System NumberingEnter the digits you want to change Specify the length of the code you want to change Description Cont’dAssign a function to the code selected Dial Types Dial Type Description Related ProgramNumber Default New System NumberingNumber of Digits Required Program 11 System Numbering Program 11 System Numbering Program 11 System Numbering Program 11 System Numbering Program 11 System Numbering To enter data for Program 11-01 System Numbering Feature Cross ReferenceInput Data Default Description Related Program Trunk Access CodeTo enter data for Program 11-09 Trunk Access Code For Your Notes Program 14 Trunk, Basic Setup Basic Trunk Data SetupInput Data Default Related Program Trunk Port Number Name To enter data for Program 14-01 Basic Trunk Data SetupTrunk Group Trunk Group Number Order NumberTrunk Port Group Priority To enter data for Program 14-05 Trunk Group Trunk Port Number Input Data Trunk Access Map SetupNn Access Mapnnn nnnnn To enter data for Program 14-07 Trunk Access Map SetupBasic Extension Data Setup Program 15 Extension, Basic SetupInput Data Default Related Isdn Caller IDNn TELnnn nnnnn To enter data for Program 15-01 Basic Extension Data SetupTrunk Ring Tone Multi-Line Telephone Basic Data SetupIncoming Signal Frequency Pattern Type Modulation Feature Cross ReferenceDay/Night Mode Trunk Access Map No Default Related Program Trunk Access Map for Extensions15-06-01 TEL301 Mode1 Acc-Map Back ↑ ↓ select Programmable Function Keys Line Key Function Number Additional dataRed On Active To enter data for Program 15-07 Programmable Function Keys Feature Cross ReferenceTrunk Loop Access Key Operating Program 20 System Option SetupSystem Options for Multi-Line Telephones ModeTRK-GPKeyOP 0Display Back ↑ ↓ select Day/Night Mode Class of Service for Extensions Class of Service for Extensions20-06-01 TEL301 Mode1 ClassNo.1 01-14 Class of Service Options Outgoing Call ServiceTrunk Calls Department Group Step CallingFctn Cls1 IntercomCall 1On Sub Address Identiﬁcation Class of Service Options Incoming Call ServiceFctn Cls1 2ndCallDDI-Ovrride0Of Back ↑ ↓ select Class of Service Options Supplementary Service COSDisplay the Reason for Transfer Fctn Cls1 LongConv.Alarm 1On Back ↑ ↓ select Ring Cycle Setup Incoming Signal Type Ringing Cycle DefaultNumber Ringing Cycle Number To enter data for Program 20-15 Ring Cycle SetupSystem Options for Caller ID Wait Facility IE TimerFor Your Notes Program 21 Outgoing Call Setup System Options for Outgoing CallsTrunk Interdigit Time External Input Default Related Data Repeat Dial SetupTo enter data for Program 21-08 Repeat Dial Setup Calling Party Number Data Default Isdn Calling Party Number Setup for TrunksTrunk1 CLIPNo Back ↑ ↓ select Isdn Calling Party Number Setup for Extensions 21-13-01 TEL301 CLIPNo Back ↑ ↓ select Individual Trunk Group Routing for Extensions Day/Night Mode Route table number Default21-15-01 TEL301 Mode1 -T.G.R Back ↑ ↓ select For Your Notes Program 22 Incoming Call Setup Input Data Default Description RelatedSystem Options for Incoming Calls 100 Telephone Programming InstructionsDay/Night Incoming Type Default Description Related Incoming Call Trunk Setup102 To enter data for Program 22-02 Incoming Service Type SetupRing Tone Pattern Default Description Related Trunk Ring Tone RangeFrequency 104 To enter data for Program 22-03 Trunk Ring Tone RangeIncoming Ring Extension Description Related Incoming Extension Ring Group Assignment106 Nn INC Groupnnn nnnnnIncoming Trunk Ring Group Assignment Day/Night Incoming Group Default Description Related108 Day/Night Incoming Group Number Default Related Program Normal Incoming Ring Mode110 To enter data for Program 22-06 Normal Incoming Ring ModeDIL/IRG No Answer Destination Day/Night Mode Incoming Group Number Default112 Use this keypad digit When you want to Did Translation Number ConversionKey for Entering Names 114 Ring Group TransferAspire Isdn PRI Manual 115 For Your Notes 116 Program 35 Smdr Options Smdr Output OptionsTrunk Name or Received Dialed Number 118 To enter data for Program 35-02 Smdr Output OptionsProgram 81 Basic Hardware Setup for Trunk Coiu Initial Data SetupFlash Hooking 120 Feature Cross ReferenceTelephone Programming Instructions To enter data for Program 81-01 Coiu Initial Data SetupFor Your Notes 122 Incoming Ring Tone Program 82 Basic Hardware Setup for Extension124 Incoming Ringing Tone Frequency Modulation Tone NumberTo enter data for Program 82-01 Incoming Ring Tone Telephone Programming InstructionsFor Your Notes 126 Other Important Telephone Numbers 0893212