7. Appendix
Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Indicator Messages
Power Indicator
| Indicator Condition | Projector Condition | Note | ||
|
|
|
|
|
|
|
| Off | The main power is off | – | |
Blinking light | Green |
| 0.5 sec On, | The projector is getting ready to turn on. | Wait for a moment. |
|
|
| 0.5 sec Off |
|
|
|
|
| 2.5 sec On, | Off Timer is enabled. | – |
|
|
| 0.5 sec Off |
|
|
| Orange |
| 0.5 sec On, | The projector is cooling down. | Wait for a moment. |
|
|
| 0.5 sec Off |
|
|
Steady light | Green |
|
| The projector is turned on. | – |
| Orange |
|
| The projector is in Standby. | – |
Status Indicator |
|
|
|
| |
|
|
|
| ||
| Indicator Condition | Projector Condition | Note | ||
|
|
|
|
| |
|
| Off | Normal or Standby | – | |
|
|
|
| [STANDBY MODE]) |
|
Blinking light | Red |
| 1 cycle (0.5 sec On, | Lamp cover error or lamp housing error | Replace the lamp cover or lamp |
|
|
| 2.5 sec Off) |
| housing correctly. |
|
|
| 2 cycle (0.5 sec On, | Temperature error | The projector is overheated. Move the |
|
|
| 0.5 sec Off) |
| projector to a cooler location. |
|
|
| 3 cycle (0.5 sec On, | Power error | Power unit is not working properly. |
|
|
| 0.5 sec Off) |
| Contact your dealer. |
|
|
| 4 cycle (0.5 sec On, | Fan error | Fans will not work correctly. |
|
|
| 0.5 sec Off) |
|
|
|
|
| 6 cycle (0.5 sec On, | Lamp error | Lamp fails to light. Wait a full minute |
|
|
| 0.5 sec Off) |
| and then turn on again. |
| Green |
|
| The projector is | |
|
|
|
| down.) | Wait for a moment. |
Steady light | Green |
|
| Standby ([NORMAL] for [STANDBY MODE]) | – |
| Orange |
|
| Cabinet button is locked | You have pressed cabinet button |
|
|
|
|
| when Cabinet Button is locked. |
Lamp Indicator |
|
|
|
| |
|
|
|
| ||
| Indicator Condition | Projector Condition | Note | ||
|
|
|
|
| |
|
| Off | Normal | – | |
Blinking light | Red |
|
| Lamp has reached its end of life. Lamp re- | Replace the lamp. |
|
|
|
| placement message will be displayed. |
|
Steady light | Red |
|
| Lamp has been used beyond its limit. The | Replace the lamp. |
|
|
|
| projector will not turn on until the lamp is |
|
|
|
|
| replaced. |
|
| Green |
|
| Lamp mode is set to Eco mode | – |
Over-Temperature Protection
If the temperature inside the projector rises too high, the
Should this happen, do the following:
•Unplug the power cable after the cooling fans stop.
•Move the projector to a cooler location if the room where you are presenting is particularly too warm.
•Clean the ventilation holes if they are clogged with dust.
•Wait about 60 minutes until the inside of the projector becomes cool enough.
75