5
Terminal BoardC B AVIDEO 1 | VIDEO 2 | RGB AUDIO |
|
| RGB 1 | SPEAKER SELECT | REMOTE | PC/EXT CTL | ||||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
| IN |
|
| INT | EXT | IN |
|
|
|
|
|
|
|
|
| EXT SPEAKER |
| |||
BNC | S | BNC | S | R L (MONO) |
|
|
|
|
| |||
|
|
| RIGHT | LEFT |
|
| ||||||
|
|
|
|
|
|
| ||||||
IN |
| IN |
| IN |
| THROUGH |
|
| SPEAKRES MUST |
| OUT |
|
|
|
|
|
|
|
|
| HAVE MORE THAN |
|
| ||
|
|
|
|
|
| OUT |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
| THROUGH |
|
|
| 5WATT RATING |
|
|
| |
|
|
|
|
|
|
|
|
|
|
| ||
THROUGH |
|
|
|
|
|
|
| INPEDANCE 8 OHM |
|
|
| |
| THROUGH |
| OUT |
|
|
| 75Ω |
|
|
| ||
OUT |
|
|
|
| HIGH |
|
|
| DIP SW | |||
| OUT |
|
|
|
|
|
|
| ||||
|
|
|
|
| RGB 2 |
|
|
|
| ON | ||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
| R/CR/PR | G/Y/Y | B/CB/PB |
| H/CS | V |
|
| 1 2 3 4 5 6 7 8 |
|
|
|
|
|
|
|
|
|
|
|
| |
HIGH | 75Ω | HIGH | 75Ω | IN |
|
|
|
|
|
|
|
|
AUDIO | AUDIO |
|
|
|
|
|
|
| AC IN | |||
|
|
|
|
|
|
|
| |||||
R | L (MONO) | R | L (MONO) |
|
|
|
|
|
|
|
|
|
IN |
| IN |
| THROUGH |
|
|
|
|
|
|
|
|
|
|
|
| OUT |
|
|
|
|
|
|
|
|
THROUGH |
| THROUGH |
|
|
|
|
|
|
|
|
|
|
OUT |
| OUT |
| HIGH |
| 75Ω |
| HIGH | 75Ω |
|
|
|
APC/ECT CTL IN
This terminal is used when power ON/OFF, input selection, AUDIO MUTE, PICTURE MUTE, and DEGAUSS are operated externally (by external control). See also page 42 for external control port pin assignments. You can also use this connector to connect your PC to control the MultiSync XP37 Xtra/XM37 Xtra monitor. This allows you to utilize your PC and serial communication protocol to control the monitor.
NOTE: Select EXT. CONTROL ON by setting pin No. 6 of DIP SW to the ON position when operating the monitor by external control. NOTE: When in the EXT. CONTROL mode, the following operations of the supplied wireless remote control are not possible: Power control ON/ OFF, Input selection, and Degauss switch ON/ OFF.
PC/ECT CTL OUT
EXTERNAL CONTROL input to relay the signal input at the EXTERNAL CONTROL IN. The EXTERNAL CONTROL OUT terminal is used to connect several monitors together and allows all of the monitors to be controlled by one external control. No. 6 pin (EXT. CONTROL) of DIP SW must be set to the ON position on all of the monitors.
BREMOTE IN/OUT
Connect the optional remote cable, included with the optional remote control, to the REMOTE IN terminal. The REMOTE OUT terminal is used to connect several monitors together and allows all of the monitors to be controlled by one remote control.
NOTE: Up to 50 monitors can be connected in the serial connection. (This can be done only when the optional supplied remoto cable is used.)
CEXT SPEAKER
RIGHT + ....... Connect RIGHT speaker positive wire here. RIGHT
LEFT + ......... Connect LEFT speaker positive wire here. SPEAKER SELECT INT/EXT Select Switch.....Set to the INT position for
NOTE: The speaker cables must be less than 3m in length.
DDIP Switch
DIP SW..... This DIP switch sets Sync. Control, the Intelligent Power Manager, external control on/off, remote control on/off, and OSM system control on/off. See pages 17 and 18 for more
details.
EAC Input
Connect the supplied power cord’ s
VIDEO 1 | VIDEO 2 | RGB AUDIO | RGB 1 | SPEAKER SELECT | REMOTE | PC/EXT CTL |
|
|
|
| EXT SPEAKER |
|
|
|
|
| RGB 2 |
|
| DIP SW |
|
|
|
|
|
| |
AUDIO | AUDIO |
|
|
|
| AC IN |
Insert the prongs completely.
6
8