Manuals / Brands / Computer Equipment / Projector / NEC / Computer Equipment / Projector

NEC XL-6500, XL-6500G 2. INSTALLATION, Setting Up Your MultiSync Hivid 6500 Projector, Moving The Projector, Pulling Out the Handles, Retracting the Handles, Selecting A Location

1 82

Download 82 pages, 658.47 Kb

12345623456777771123456123456123456 2. INSTALLATION

1234567

This section describes how to set up your MultiSync Hivid

6500 projector and how to connect video and audio sources.

Setting Up Your MultiSync Hivid 6500 Projector

To set up and use your MultiSync Hivid 6500 Projector, you must first do:

1.Determine the screen size and the optional lens to be used.

NOTE: Consult your dealer for lens order and installation.

2.Set up a screen or select a non-glossy white wall onto which you can project your image.

Moving The Projector

Always carry your projector by the handle. Ensure that the power cord and any other cables connecting to video sources are disconnected before moving the projector. When moving the projector or when it is not in use, cover the lens with the lens cap.

Pulling Out the Handles

Pull out the handle from the bottom side.

Retracting the Handles

Press down the two levers at the same time to retract the handle.

Selecting A Location

The further your projector is from the screen or wall, the larger the image. The minimum size the image can be projected is 80" (2 m) measured diagonally. The largest the image can be is 500" (12.7 m).

WARNING

•Only use your projector on a solid, level surface. If the projector falls to the ground, you can be injured and the projector severely damaged.

•Do not use the projector where temperatures vary greatly. The projector must be used at temperatures between 50 degrees F (10 degree C) and 104 degrees F (40 degree C).

•Do not expose the projector to moisture, dust, or smoke. This will harm the screen image.

•Ensure that you have adequate ventilation around your projector so heat can dissipate. Do not cover the vents on the bottom or back of the projector.

16

Contents

MultiSync Hivid 6500 Projector CAUTION: 3. GSGV Acoustic Noise Information Ordinance: WARNING Precautions AVERTISSEMENT Installation Power Supply Cleaning Fire and Shock Precautions Alimentation Nettoyage Précautions contre l'incendie ou la décharge LIMITED WARRANTY INTRODUCTION 1.PART NAMES AND FUNCTIONS 2.INSTALLATION 3. OPERATION 4. SPECIFICATIONS INTRODUCTION Congratulations On Your Purchase Of The MultiSync Hivid 6500 Projector Features you’ll enjoy : How Do You Get Started What’s In The Box 1.PART NAMES AND FUNCTIONS 1.PART NAMES AND FUNCTIONS H I J K L M N BOPTION Connectors (D-Sub 9-pin) CREMOTE 1 Connector (Mini D-Sub 15-pin) DINPUT E OPTIONAL Boards Rotary switch (S1001) Jumper (S1002, S1003, S1004) Setting of Rotary switch No Mark Remote control unit BHELP Button CSIG LEVEL Button DGAMMA Button EADDRESS Button FPIXEL CLK Button Remote Control Battery Installation 1. Press firmly and slide the battery cover off 2. Remove both old batteries and install new ones (AA) Ensure that you have the batteries’ polarity (+/-)aligned correctly 3. Slip the cover back over the batteries until it snaps into place When using the remote control as the key panel on the projector: 2. INSTALLATION Setting Up Your MultiSync Hivid 6500 Projector Moving The Projector Pulling Out the Handles Retracting the Handles Screen Size and Projection Distance Ceiling Installation ■Projection model : XL-3500/3500G ■Projection model : XL-6500/6500G Reflecting The Image Rear Screen Projection EXAMPLES OF CONNECTIONS CAUTIONS ON CONNECTIONS: When Used with One Switcher (ISS-6020/ISS-6020G) How to make connections: Set the DIP switch (S8601) of the Switcher as follows: When used with the Switcher When used in stand alone operation 3.OPERATION General Controls Using The On-ScreenMenus When a passcode has not been registered: When your passcode has already been registered: Menu Descriptions & Functions Storing Projector Settings (Automatic Save Feature) Basic Operation (Operate Menu) When using the projector in stand alone operation: When using the projector with the ISS-6020/ISS-6020G: When using the projector with two ISS-6020/ISS-6020Gor more: Source Information ■Source Name ■Direct Key ■Input Slot ■Display Mode ■Sync System ■Sync Termination ■Scale Mode ■Input Sig. Size ■Output Sig. Size ■CTI(Color Transient Improvement) Control ■Noise Reduction ■Source Select Counter ■Source Display Timer Picture Control Lens Control ■Pixel Clock / Pixel Phase ■Zoom/Pan ■Image Position ■Blanking Sound Control (only when used with the ISS-6020/ISS-6020GSwitcher) Closed Caption Timer Setting Page Adjusting and Setting (Adjustment) ■Source Registry 1)To Select a Slot When using with a single Switcher ISS-6020/ISS-6020G: When using with two or more ISS-6020/ISS-6020Gswitchers: 2)To Select Signal System To Set HDTV or not When Selecting Component Signal 4)To Input a User Name 5)To Select a Registry Number ■Registry Edit Amplitude White Balance Signal Level Uniformity To Adjust White Uniformity To Adjust the Edge Blending Display Function 1) Input Signal Size 2) Output Signal Size 3) Output Position 4)Interlace Mode Lamp Mode ■Entering Passcode ■Registering Passcode Page ■Changing Your Passcode Page ■Canceling Your Passcode Page ■PJ Orientation ■Default Source Select When used in stand alone operation: The default input screen will be displayed When used with a single Switcher: When used with two or more Switchers: ■S-VideoMode Select ■Video System Select ■Auto Data Store ■Option Terminal Speed ■Uniformity Switching ■Message Time Page ■Date, Time Preset ■Display Item Set ■Connect Condition ■PJ Address mAddressing the Remote Control Unit Address common to all the projectors A D D R E S S R C U N I T ∗∗ ■Help ■Topics ■Set Information ■Test Patterns ■Normal, Load, and Cancel Function ■To return to the last stored level (Load): ■To cancel the adjustment data (Cancel): Page Page 5.APPENDIX Page NEC Corporation