NEC XL-6500, XL-6500G 78

1234567	4.SPECIFICATIONS
123456123456123456123456123456 77777
1234567

Projection Type	: 3Chip DMD TM High light output projector.
Projection System	: 3chip DMD TM , 1 Lens
Display Orientation	: Front Floor , Rear Floor ,
	Front Ceiling , Rear Ceiling
Lamp Type	: Bulb type 1.6 KW Xenon Lamp
Shooting offset	: Common lens for both XL-3500 and XL-6500
	Fixed lens ........................................... 0±150 pixels
	Zoom lens .......................................... 0
	Lens for XL-6500 only
	HVL-X1Z/HVL-X2Z ............................ 0±360 pixels
	HVL-X3Z ............................................ 0±200 pixels
Scanning line rat	: H 15-80KHz
/ Flame rate	V 30-120Hz
Resolution	: DMDTM 10243768 pixel
	Max : 1280 3 1024 by Scaling
Pixel clock	: Max 80 MHz
Lens (optional)	: Fixed lens (common lens for both XL-3500 and XL-6500)
	XL-L1.27 : 1.27:1 (for XL-3500) / 1.0:1 (for XL-6500)
	XL-L3 : 3.0:1 (for XL-3500) / 2.3:1 (for XL-6500)
	XL-L5 : 5.0:1 (for XL-3500) / 3.9:1 (for XL-6500)
	XL-L7 : 7.0:1 (for XL-3500) / 5.5:1 (for XL-6500)
	Zoom Lens (common lens for both XL-3500 and XL-6500)
	XL-L1.5Z : 1.5-3.0 (for XL-3500) / 1.2-2.3 (for XL-6500)
	XL-L3Z :		3.0-7.0 (for XL-3500) / 2.3-5.5 (for XL-6500)
	Zoom Lens (for XL-6500 only)
	HVL-X1Z : 1.5-2.5
	HVL-X2Z : 2.5-4.0
	HVL-X3Z : 4.0-7.0
Picture Size	: 80-500 inch diagonal
Light Output	: 6500 ANSI lumen
Contrast Ratio	: 350:1 ( Full On / Off )
Input terminal	:
	Fixed terminal :
			Composite Video ( BNC or RCA switchable )
			RGB , H, V / Y,Cr,Cb ( BNC )
			S Video	( S- terminal )
	Optional terminal :
			2 slot prepared
Input signal (Level)	: RGB signal : 0.7Vp-p 75ohm Positive(BNC)
	HV sync	:	0.7-4.0Vp-p(75ohm/1Kohm)
			Negative or Positive(BNC)
			Duty 3-30% (H-Sync Positive)
			70-97% (H-Sync Negative)
			0.1-10%(V-sync Positive)
			90-99.9%(V-Sync Negative)
	Mix sync	:	0.7-4.0Vp-p(75ohm/1Kohm)
			Negative or Positive(BNC)

78

Contents

MultiSync Hivid 6500 Projector CAUTION: 3. GSGV Acoustic Noise Information Ordinance: WARNING Precautions AVERTISSEMENT Installation Power Supply Cleaning Fire and Shock Precautions Alimentation Nettoyage Précautions contre l'incendie ou la décharge LIMITED WARRANTY INTRODUCTION 1.PART NAMES AND FUNCTIONS 2.INSTALLATION 3. OPERATION 4. SPECIFICATIONS INTRODUCTION Congratulations On Your Purchase Of The MultiSync Hivid 6500 Projector Features you’ll enjoy : How Do You Get Started What’s In The Box 1.PART NAMES AND FUNCTIONS 1.PART NAMES AND FUNCTIONS H I J K L M N BOPTION Connectors (D-Sub 9-pin) CREMOTE 1 Connector (Mini D-Sub 15-pin) DINPUT E OPTIONAL Boards Rotary switch (S1001) Jumper (S1002, S1003, S1004) Setting of Rotary switch No Mark Remote control unit BHELP Button CSIG LEVEL Button DGAMMA Button EADDRESS Button FPIXEL CLK Button Remote Control Battery Installation 1. Press firmly and slide the battery cover off 2. Remove both old batteries and install new ones (AA) Ensure that you have the batteries’ polarity (+/-)aligned correctly 3. Slip the cover back over the batteries until it snaps into place When using the remote control as the key panel on the projector: 2. INSTALLATION Setting Up Your MultiSync Hivid 6500 Projector Moving The Projector Pulling Out the Handles Retracting the Handles Screen Size and Projection Distance Ceiling Installation ■Projection model : XL-3500/3500G ■Projection model : XL-6500/6500G Reflecting The Image Rear Screen Projection EXAMPLES OF CONNECTIONS CAUTIONS ON CONNECTIONS: When Used with One Switcher (ISS-6020/ISS-6020G) How to make connections: Set the DIP switch (S8601) of the Switcher as follows: When used with the Switcher When used in stand alone operation 3.OPERATION General Controls Using The On-ScreenMenus When a passcode has not been registered: When your passcode has already been registered: Menu Descriptions & Functions Storing Projector Settings (Automatic Save Feature) Basic Operation (Operate Menu) When using the projector in stand alone operation: When using the projector with the ISS-6020/ISS-6020G: When using the projector with two ISS-6020/ISS-6020Gor more: Source Information ■Source Name ■Direct Key ■Input Slot ■Display Mode ■Sync System ■Sync Termination ■Scale Mode ■Input Sig. Size ■Output Sig. Size ■CTI(Color Transient Improvement) Control ■Noise Reduction ■Source Select Counter ■Source Display Timer Picture Control Lens Control ■Pixel Clock / Pixel Phase ■Zoom/Pan ■Image Position ■Blanking Sound Control (only when used with the ISS-6020/ISS-6020GSwitcher) Closed Caption Timer Setting Page Adjusting and Setting (Adjustment) ■Source Registry 1)To Select a Slot When using with a single Switcher ISS-6020/ISS-6020G: When using with two or more ISS-6020/ISS-6020Gswitchers: 2)To Select Signal System To Set HDTV or not When Selecting Component Signal 4)To Input a User Name 5)To Select a Registry Number ■Registry Edit Amplitude White Balance Signal Level Uniformity To Adjust White Uniformity To Adjust the Edge Blending Display Function 1) Input Signal Size 2) Output Signal Size 3) Output Position 4)Interlace Mode Lamp Mode ■Entering Passcode ■Registering Passcode Page ■Changing Your Passcode Page ■Canceling Your Passcode Page ■PJ Orientation ■Default Source Select When used in stand alone operation: The default input screen will be displayed When used with a single Switcher: When used with two or more Switchers: ■S-VideoMode Select ■Video System Select ■Auto Data Store ■Option Terminal Speed ■Uniformity Switching ■Message Time Page ■Date, Time Preset ■Display Item Set ■Connect Condition ■PJ Address mAddressing the Remote Control Unit Address common to all the projectors A D D R E S S R C U N I T ∗∗ ■Help ■Topics ■Set Information ■Test Patterns ■Normal, Load, and Cancel Function ■To return to the last stored level (Load): ■To cancel the adjustment data (Cancel): Page Page 5.APPENDIX Page NEC Corporation