NEC XP29 Plus, XM29 Plus Daisy-chainingYour monitors, D-Sub15 Pin RGB Signal Composition, Pin No

Daisy-chaining Your monitors

The REMOTE IN/OUT terminals allow you to control monitors by one remote control.

NOTE: The connection of three XP29 Plus/XM29 Plus monitors or more with THROUGH OUT (VIDEO 1 or 2) terminals may degrade image quality.

To do so:

When using the VIDEO inputs:

THROUGH OUT (VIDEO 1) Connections

1.Connect THROUGH OUT 1 BNC or S-VIDEO 1 OUT to external compo- nents to relay the signal input at VIDEO 1 IN(BNC-type), or S-VIDEO 1 IN.

2.Connect the external component mono audio or stereo left channel audio input to L AUDIO.

3.Connect the external component stereo right channel audio input to R AU- DIO.

4.Set the 75Ω/HIGH impedance select switch of the corresponding input sig-

nal (BNC, S-VIDEO) on all but the last monitor to “HIGH” position. On only the last monitor is set to “75Ω” position.

THROUGH OUT (VIDEO 2) Connections

1.Connect THROUGH OUT 2 BNC or S-VIDEO 2 OUT to external component to relay the signal input at VIDEO 2 IN(BNC-type) or S-VIDEO 2 IN.

2.Connect the external component mono audio or stereo left channel audio input to L AUDIO.

23

3.Connect the external component stereo right channel audio input to R AU- DIO.

4.Set the 75Ω/HIGH impedance select switch of the corresponding input signal

(BNC, S-VIDEO) on all but the last monitor to “HIGH” position. On only the last monitor is set to the “75Ω” position.

5.Connect the REMOTE OUT of the monitor to the REMOTE IN of the next monitor using the optional remote cable.

When using the RGB inputs:

THROUGH OUT Connections

1.(RGB1): Connect D-Sub 15-pin THROUGH OUT to an RGB input connector of other monitors.

(RGB2): Connect the R.G.B.H and V THROUGH OUT terminals to relay the signal input at the R.G.B.H and V IN terminals.

2.Set all the 75Ω/HIGH impedance select switches on all but the last monitor to “HIGH” position. On only the last monitor is set to the “75Ω” position.

3.Connect the REMOTE IN of the monitor to the REMOTE OUT of the next monitor using the optional remote cable.

NOTE: ''Plug and Play'' is available only for the monitor connected directly to a personal computer with the D-Sub 15-pin RGB connector. Therefore, ''Plug and Play'' does not work for monitors connected with the THROUGH OUT terminal. This is because only the RGB video, the horizontal, and the vertical sync. signal is output from the THROUGH OUT terminals.

NOTE: ''Plug and Play'' is not available for the RGB 2 BNC terminals.

D-Sub 15 Pin RGB Signal Composition

Pin Assignments and Signal Levels for 15 pin RGB (Analog)

8 7 6 5 4 3 2 1

15 14 13 12 11 10 9

D-SUB 15pin RGB Input Connector (ANALOG ONLY)

Pin No. Signal to be connected (D-SUB 15 pin)

1RED

2GREEN or Sync Green

3BLUE

12No Connection

13H. or Composite sync

14V.SYNC

15No Connection

4GND

5GND

6GND

7GND

8GND

11 GND

10No Connection

9 No Connection

5 4 3 2 1

10 9 8 7 6

15 14 13 12 11

Pin No. Through output (MAC 15 pin)

2RED

5GREEN or Sync Green

9BLUE

7SDA (PnP)

3H. or Composite sync

12V.SYNC

15SCL (PnP)

1	GND
4	GND
6	GND
11	GND
13	GND

8No Connection

10 No Connection

14 No Connection

24