9
Terminal Board
I J KSPEAKERS MUST HAVE |
|
| VIDEO 1 |
| RGB1 |
|
|
|
| PC / EXT CTL | |
MORE THAN 5WATT RATING |
| BNC |
|
| DIP SW | REMOTE | |||||
IMPEDANCE 8 OHM | 75 | S | AUDIO |
|
|
| |||||
EXT SPEAKERS |
|
| 75 |
| ON |
|
|
| |||
IN | R | L(MONO) |
|
| IN |
| |||||
RIGHT | LEFT |
| IN |
|
|
|
| ||||
|
|
|
|
|
|
|
| ||||
|
| HIGH | IN |
| HIGH |
| 1 2 3 4 5 6 7 8 |
|
|
| |
|
|
|
|
|
|
|
| ||||
|
|
| THROUGH | THROUGH |
| THROUGH |
|
|
| OUT |
|
|
|
| OUT | OUT |
| OUT |
|
|
|
|
|
SPEAKER SELECT |
| BNC | VIDEO 2 |
| RGB AUDIO | R/CR/PR | RGB 2 | B/CBPB | H/CS | V | |
INT | EXT |
| S | AUDIO |
| G/Y/Y | |||||
AC IN | � 75 |
|
|
| 75 IN |
|
|
| 75 | ||
IN | R | L(MONO) | R L(MONO) |
|
|
| |||||
|
| HIGH | IN |
| IN | HIGH |
|
|
| HIGH | |
|
|
| THROUGH | THROUGH |
| THROUGH | THROUGH |
|
|
|
|
|
|
| OUT | OUT |
| OUT | OUT |
|
|
|
|
H
HRGB 2
R/CR/PR, G/Y/Y, B/CB/PB/ H/CS and V IN (BNC) ... These are analog RGB and component signal input terminals. Connect external components with R, G, B, H, and V output terminals to these analog RGB input terminals. Be sure that the RGB connection cable is correctly attached to the corresponding terminals.
R/CR/PR, G/Y/Y, B/CB/PB/ ,H/CS and V THROUGH OUT (BNC) ...... Connect to a second monitor’s RGB inputs to relay the RGB signal inputs at R, G, B, H, and V IN.
75 Ω/HIGH Impedance Select Switches for RGB and HV .... S e t t o “ 7 5 Ω ”
during normal operation. In multiple connections using R, G, B, H and V IN and OUT terminals, set to “HIGH” on all but the last monitor. Set to “75 Ω” on the last monitor only.
IDIP Switch
DIP SW ..... This DIP switch sets Sync. Control, the Intelligent Power Manager, external control on/off, remote control on/off, and OSM control menu control on/off. See pages 17 and 18 for more details.
JREMOTE IN/OUT
Connect the optional remote cable, included with the optional remote control, to the REMOTE IN terminal. The REMOTE OUT terminal is used to connect several monitors together and allows all of the monitors to be
controlled by one remote control.
NOTE: Up to 50 monitors can be connected in the serial connection (This can be done only when the supplied remote cable is used.).
KPC/EXT CTL
This terminal is used when power ON/OFF, input selection, AUDIO MUTE, PICTURE MUTE, and DEGAUSS are operated externally (by external control). See also page 46 for external control port pin assignments. You can also use this connector to connect your PC to control the MultiSync XP29 Xtra/XM29 Xtra monitor. This allows you to utilize your PC and serial communication protocol to control the monitor.
NOTE: Select EXT. CONTROL ON by setting pin No. 6 of DIP SW to the ON position when operating the monitor by external control. NOTE: When in the EXT. CONTROL mode, the following operations of the supplied wireless remote control are not possible: Power control ON/ OFF, Input selection, and Degauss switch ON/OFF.
PC/EXT CTL OUT
10
10