3
Part Names and Functions
Front View | Rear View |
PROCEED | VIDEO 1 | VIDEO 2 | RGB 1 | RGB 2/DTV |
EXIT | ▼� | �▼ | �－� | ＋� |
POWER
/STANDBY
9 8 7 6 5 4 3 2 1
SPEAKERS MUST HAVE |
| VIDEO 1 |
|
| RGB1 |
|
|
|
| PC / EXT CTL | |
MORE THAN 5WATT RATING | BNC |
|
|
| DIP SW | REMOTE | |||||
IMPEDANCE 8 OHM | S |
| AUDIO |
|
|
| |||||
EXT SPEAKERS | 75 |
|
| 75 |
|
|
| IN |
| ||
RIGHT | LEFT | IN |
| R | L(MONO) | IN |
|
|
|
| |
|
| HIGH | IN |
|
| HIGH |
|
|
|
|
|
|
| THROUGH | THROUGH |
|
| THROUGH |
|
|
| OUT |
|
|
| OUT | OUT |
|
| OUT |
|
|
|
|
|
SPEAKER SELECT |
| VIDEO 2 |
|
| RGB AUDIO |
| RGB 2 |
|
|
| |
BNC | S |
|
|
| R/C /P | G/Y/Y | B/C P | H | V | ||
INT | EXT | 75 |
|
| AUDIO |
| 75 |
|
|
| 75 |
AC IN |
| IN |
| R | L(MONO) | R L(MONO) | IN |
|
|
|
|
|
| HIGH | IN |
|
| IN | HIGH |
|
|
| HIGH |
|
| THROUGH | THROUGH |
|
| THROUGH | THROUGH |
|
|
|
|
|
| OUT | OUT |
|
| OUT | OUT |
|
|
|
|
POWER
/STANDBY
0 |
| Terminal Board |
|
1 POWER .............................. | Press to turn the main power on and off when |
| the AC power is supplied. |
2 POWER/STANDBY ........ | When this indicator is green, the monitor is |
| on; when the indicator is amber, it is in stand |
| by. |
3Remote Sensor Window ... Receives infrared signal from the handheld
remote control.
4 RGB 2/DTV/+ ...................... | Press to select an RGB or component video |
| source that is connected to the RGB 2 input |
| terminals (BNC type). When you are in the |
| OSM mode, this button works as the plus |
| button. |
5 RGB | Press to select an RGB video source that is |
| connected to the RGB 1 input terminal (D- |
| SUB 15 pin type). |
| When you are in the OSM mode, this button |
| works as the minus button. |
6 VIDEO 2/ .......................... | Press to select an NTSC, PAL, SECAM or M- |
| NTSC compatible video source that is |
| connected to the VIDEO 2 input terminal (BNC |
| type or |
| OSM mode, this button works as the up button. |
|
|
| NOTE: |
| preference over VIDEO IN terminals when |
| the video source is connected to each |
| terminal and VIDEO 1 or 2 selected. |
.........................7 VIDEO 1/ | Press to select an NTSC, PAL, SECAM or M- |
| NTSC compatible video source that is |
| connected to the VIDEO 1 input terminal (BNC |
| type or |
| OSM mode, this button works as the down |
| button. |
8 EXIT .................................... | Press to exit the OSM mode. The OSM screen |
| disappears. |
9 PROCEED .......................... | Press to access OSM. The OSM screen is |
| displayed. |
0Remote Control Holder ..... Place remote control unit here when not in use.
4
7