b.Follow the Smart Wizard prompts to connect to the Internet.
c.When prompted, enable your wireless network, click Next to proceed, then click Done and Ok to close the screen and finish.
Note: The configuration assistant only appears when the router is in its factory default state. After you configure the wireless router, it will not appear again. You can always connect to the router
configuration menu to change its settings. To do so, open a browser and go to http://www.routerlogin.net. Then, when prompted, enter admin as the user name and password for the password both in lower case letters.
You are now connected to the Internet and the wireless feature of the wireless router is enabled! Next, configure your wireless computer.
Now, Set Up a Computer for Wireless Connectivity
1.CONFIGURE THE COMPUTER’S WIRELESS SETTINGS
NETGEAR, Inc. wireless adapters display a list of available wireless networks, and, when wireless security is disabled, you simply choose yours from the list and connect.
For a
WIRELESS FEATURE | DEFAULT SETTING |
Network Name (SSID) | NETGEAR |
|
|
WEP Security | Disabled |
Warning: The Network Name is case sensitive. Entering nETgear will not work.
July 2004
2.VERIFY WIRELESS CONNECTIVITY
Connect to the Internet from a computer with a wireless adapter. You are now wirelessly connected to the Internet!
Important: Implement wireless security options appropriate to your needs. These settings enable basic wireless connectivity that let you set up your wireless computers and test wireless Internet access through the router.
The NETGEAR wireless router provides many wireless security options. Your wireless computer may not support all of these options. Please read the NETGEAR manual to identify the wireless security features of your router that satisfy your requirements and work with your wireless computer.
Troubleshooting Tips
Here are some tips for correcting simple problems you may have.
Be sure to restart your network in this sequence:
1)Turn off the modem, wireless router, and computer; 2) Turn on the modem, wait two minutes; 3) Turn on the wireless router and wait 1 minute; 4) Turn on the computer.
Make sure the Ethernet cables are securely plugged in.
•The Internet status light on the wireless router will be lit if the Ethernet cable to the wireless router from the modem is plugged in securely and the modem and wireless router are turned on.
•For each powered on computer connected to the wireless router with a securely plugged in Ethernet cable, the corresponding wireless router LAN port status light will be lit. The label on the bottom of the wireless router identifies the number of each LAN port.
Make sure the wireless settings in the computer and router match exactly.
The Wireless Network Name (SSID) and WEP security settings of the router and wireless computer must match exactly.
Make sure the network settings of the computer are correct.
•Ethernet cable and wirelessly connected computers must be configured to obtain IP and DNS addresses automatically via DHCP. For help with this, please see the animated tutorials on the CD or the Reference Manual Appendix C on the CD.
•Some cable modem ISPs require you to use the MAC address of the computer registered on the account. If so, in the Router MAC Address section of the Basic Settings menu, select, “Use this Computer’s MAC Address.” The router will then capture and use the MAC address of the computer that you are now using. You must be using the computer that is registered with the ISP. Click Apply to save your settings. Restart the network in the correct sequence.
Check the router status lights to verify correct router operation.
•If the Power light does not turn solid green within 2 minutes of turning the router on, reset the router as described in the Reference Manual on the CD.
•If the Wireless light does not come on, verify that the wireless feature is turned on according to the instructions in the Reference Manual on the CD.
Advanced user access.
Technically advanced users who want to bypass the configuration assistant can do so by logging in to the router at http://www.routerlogin.net/basicsetting.htm with the user name of admin and the password of password in lower case letters.
Technical Support
Thank you for selecting NETGEAR products.
After completing the Smart Wizard configuration assistant, register your product at http://www.NETGEAR.com/register. Registration is required before you can use our telephone support service.
Go to wireless router http://kbserver.netgear.com/products/WGR614v5.asp for product updates and web support.
Attention: When you configure the wireless settings of this device
0560 please make sure to select the correct country settings. Due to EU law, the country settings must be identical to the country where
the device is operating (important due to
©2004 by NETGEAR, Inc. All rights reserved.
NETGEAR is a registered trademark of NETGEAR, Inc. in the United States and/or other countries.
Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice.
