TLM 170 R

a)In mittengeerdeten Geräten mit Eingangs- übertrager (z.B. einige NAGRA-Geräte) kann die betreffende Erdverbindung fast immer ohne Nach- teile für die Funktion des Gerätes aufgetrennt werden.

b)In jede abgehende Modulationsleitung kann zur Abblockung der 48 V-Gleichspannung eine RC- Kombination eingefügt werden (siehe Abbildung 2 und Neumann-Information Nr. 84 221).

a)In center tap grounded equipment with input transformer (e.g. some NAGRA units), the earth lead can almost always be disconnected without affecting the function of the equipment.

b)In every outgoing modulation lead, an RC net- work can be incorporated to block the 48 Vdc voltage (See Figure 2 and Neumann-Information no. 84 222).

eine Überwurfmutter und eine Stativgelenkkupplung besitzt (siehe Abschnitt 2.3).

Das Mikrophon kann auch in die Elastische Aufhängung EA 170 eingebaut werden, wobei der oben erwähnte Gewindering zum Festschrauben benötigt wird.

Bei Verwendung des Kabels IC 4 und der Mikrophonnei- gevorrichtung MNV 87 kann das Mikrophon TLM 170 R auch frei am Kabel hängend betrieben werden.

Mounting the TLM 170 R in the EA 170 Elastic Suspension also requires removal of the side bracket. The suspension is attached using the screw ring mentioned above.

When using the MNV 87 auditorium hanger, the TLM 170 R microphone may, of course, be suspended from its own cable (without the side bracket).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Abbildung / Figure 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4. Demontage der elastischen

 

 

 

 

 

 

 

4. Disassembling the Elastic

Bügelhalterung

 

 

 

 

 

 

 

 

 

 

Stand-Mount Bracket

Zur Demontage des schwenkbaren Bügels mit seiner Halterung sollte zunächst der Bügel schräg nach oben geschwenkt werden, damit der große Gewindering unten am Mikrophon abgeschraubt werden kann. Dann ist die Rändelschraube am oberen Gummipuffer der Halterung zu lösen, wor- aufhin Halterung und Bügel nach unten vom Mi- krophon abgezogen werden können.

Halterung und Bügel sind eine montierte Einheit, die nicht getrennt werden sollte.

Der komplette Bügel kann auch auf der anderen Seite des Mikrophons montiert werden, wo eine Groschenschlitzschraube ein zweites Gewinde für die Rändelschraube der Halterung abdeckt.

Ohne den schwenkbaren Bügel wird am An- schlussteil des TLM 170 R ein Gewinde frei zur Montage des Mikrophons an das Kabel IC 4, das

To disassemble the swivelable stand mount, first swivel it upward, thus exposing the large threaded screw ring located around the base connector. Remove this ring. Next unscrew the knurled screw at the upper elastic mount, after which the entire bracket may be withdrawn downward.

Stand coupling and bracket form a single assembly which should not be further disassembled.

The complete bracket may be mounted at the other side of the microphone. To do this, the screw with the coin slot has to be removed and exchanged with the knurled screw of the bracket.

With the bracket removed, the thread above the microphone's connector permits the attachment of an IC 4 cable, which is equipped with a swivel and a screw ring surrounding a 3-pole female Switchcraft connector (see chapter 2.3).

10

11