Manuals / New Media Technology / Computer Equipment / Network Card

New Media Technology 9212 Table of Content, Introduction, Before You Start, Interface Description

Models: 9212

1 26

Download 26 pages 9.22 Kb

Page 4

IP POWER 9212 USER MANUAL

Table of Content
1. INTRODUCTION	4
FEATURES
2.BEFORE YOU START	5
PACKAGE CONTENTS
MINIMUM SYSTEM REQUIREMENTS
3.INTERFACE DESCRIPTION	6
4.HARDWARE & SOFTWARE INSTALLATION	7
HDWARE INSTALLATION
9201 PRO HARDWARE CONNECT(RECOMMEND) ……………………………………… …
9202 PROHARDWARE CONNECT(RECOMMEND) ……………………………………… …
SOFTWARE INSTALLATION
5. INITIALIZATION	12
BASIC SETTING THROUGH ETHERNET
6. SETTING AND CONTROL THROUTH THE INTERNET	14
SENSOR SETTINGS FOR 9212
CONTROL SETTINGS FOR 9212
PASSWORD SETINGS FRO 9212
IP SETTINGS FOR 9212
SPECIAL INTER-CONTROL………………………………………………………………...
SPECIAL INTER-CONTROL………………………………………………………… …….
SMTP FOR E-MAIL : INFORM IP ADDRESS & SENSOR TRIGGER …….………….…….….
GPRS FOR CELL PHONE : SUPPORT WAP……………………………………………….
SOFTWARE ONLINE UPDATE
7. SETING 9202E THROUGH THE INTERNET	23
8. APPLICATION ASSOCIATED TO OTHER IP RPODUCTS	24
9. FAQ	25

- 3 -

VER. X.X,

Image 4

New Media Technology 9212 Table of Content, Introduction, Before You Start, Interface Description, Initialization, Faq

Contents

IP Power User ManualIP POWER 9212 USER MANUAL IP POWER Version 2005.07USER MANUAL IMPORTANT NOTICE Table of Content 4.HARDWARE & SOFTWARE INSTALLATION6. SETTING AND CONTROL THROUTH THE INTERNET 9. FAQ1. Introduction Feature︰15. Support GPRS - setting by for online Cell phone item limit 13. Embedded “ WATCH DOG “9212 package contents 2. Before you startMinimum System Requirements One set of IP POWER9202 is the output module and figure below shows its interface 3. Interface Description9202 is the output module and figure below shows its interface 4. Hardware & Software installation Hardware Installation Connect RJ45 first then POWER jack9201Pro Hardware connection recommend 1. The polarity Right - Positive & Left - NegativePage 9202 Pro Hardware connection recommend Slink mode Resistance InputSource mode Voltage input NOTICE BE CAREFUL IN THIS OPERATION AND DO NOT TOUCH THE WIRE UNDER VOLTAGE WITH ANY PART OF YOUR BODY, ESPECIALLY WITH YOUR HANDS Software installation 5. Initial SettingsInitial settings through the Ethernet IPEditV3 can adjust Name / Gateway / IP / Netmask / HTTP Port1 execute key “cmd” in dialog 6. Control and settings through the Internet Sensor of IP Power 9212 Read IOSink mode Resistance Input Source mode Voltage inputControl of IP Power 9212 SET IO 1. Auto test function2. Set the output’s state to ON/OFF Setting the password for IP Power Setting the IP address for IP PowerPage SMTP for E-Mail receive IP address & inform as Sensor trigger 2-1 For example Control Ip Motor by DI board of IP PowerStep 1 Go to SETUP , change Connect Client and set as Motor Step 2 key in the IP address of controlled device IP MotorSetting Sample Receiver 12345678@abcd.com 87654321@dcba.com Sender abcd@168.com Mail Server 168.com Mail Passwordd. Connect time out , mail to be dropped please login again Warning MSG AlertSoftware online update GPRS for Cell Phone Support WAPStep 1 Login the webpage Step 2 Click Firmware Update and click update7. Setting the 9212 through the Internet Step 4 after finish update please wait some second and then re-log InPS If use DHCP please enable DHCP Note ： 1If the Port is 80 then you can directly update。IP POWER 9212 USER MANUAL 8. Associated with other IP network product 9. FAQ