Nikon DSR-1500A, DSR-1500AP manual 64

Settings Menu 4 Chapter

TIME CODE [Time code]: Settings related to the time code		Description of settings
generator
VITC POS SEL-1 [> VITC pos-1]: Select a line to insert the		(For DSR-1500A)
VITC in.		20 LINE [>> 20 line] to 12 LINE [>> 12 line]: Select any line
		from 12 to 20.
Note		Factory default setting: 16 LINE [>> 16 line]
You can insert the VITC signal in two places. To insert it in two
		(For DSR-1500AP)
places, set both this item and also VITC POS SEL-2.		22 LINE [>> 22 line] to 9 LINE [>> 9 line]: Select any line
		from 9 to 22.
		Factory default setting: 19 LINE [>> 19 line]
VITC POS SEL-2 [> VITC pos-2]: Select a line to insert the		(For DSR-1500A)
VITC in.		20 LINE [>> 20 line] to 12 LINE [>> 12 line]: Select any line
		from 12 to 20.
Note		Factory default setting: 18 LINE [>> 18 line]
You can insert the VITC signal in two places. To insert it in two
		(For DSR-1500AP)
places, set both this item and also VITC POS SEL-1.		22 LINE [>> 22 line] to 9 LINE [>> 9 line]: Select any line
		from 9 to 22.
		Factory default setting: 21 LINE [>> 21 line]
VITC OUTPUT [> VITC out]: Select the time code to be output		OFF [>> OFF]: Do not output VITC.
as VITC.		TC [>> TC]: Output TC after converting it into VITC.
		*VITC [>> VITC]: Output VITC.
EE OUT PHASE [> EE out]: Determine the output phase for		*MUTE [>> mute]: Mute the output.
the LTC signal output from the TC OUT connector when		THROUGH [>> through]: Output the time code input to the
recording time code and in STOP REC mode (forced EE		TC IN connector as it is. (See example configuration on
mode).		page 70.)
		VIDEO INPUT PHASE [>> V input]: Output the time code
		with the same phase as the input video signal phase.
		(See example configuration on page 70.)
		VIDEO OUTPUT PHASE [>> V output]: Output the time code
		with the same phase as the output video signal phase.
		(See example configuration on page 71.)
MUTE IN SRCH [> Mute in SR]: Select whether to mute the		OFF [>> OFF]: Do not mute.
output from the TC OUT connector in search (jog/shuttle)		*ON [>> ON]: Mute.
mode.
TAPE PROTECTION [Tape protct]: Settings related to tape		Description of settings
and video head protection
FROM STOP [> From STOP]:	STOP TIMER [>> STP	0.5 SEC [>>> 0.5 sec] to 5 MIN [>>> 5 min]: Select time from
Set the time to switch from	timer]: Set the time to	12 settings ranging from 0.5 second to 5 minutes in steps
stop mode to tape protection	switch from stop mode	of 0.1 second.
mode.	to tape protection	Factory default setting: 1 MIN [>>> 1 min]
	mode.
		Note
		If the value is set to 1 minute or more, the unit enters internal
		protection mode in 1 minute, which makes start up slower.
FROM STILL [> From STILL]:	STILL TIMER [>> STL	0.5 SEC [>>> 0.5 sec] to 5 MIN [>>> 5 min]: Select time from
Set the time to switch from	timer]: Set the time to	12 settings ranging from 0.5 second to 5 minutes in steps
still search mode to tape	switch from still search	of 0.1 second.
protection mode. Also select	mode to tape	Factory default setting: 1 MIN [>>> 1 min]
the type of tape protection	protection mode.
mode.		Note
		If the value is set to 1 minute or more, the unit enters internal
		protection mode in 1 minute, which makes start up slower.
	NEXT MODE [>> Next	*STEP FWD [>>> Step]: The tape is advanced at 1/30 times
	mode]: Select the type	normal speed for about 2 seconds.
	of tape protection
		STANDBY OFF [>>> STANDBY]: Standby off mode
	mode to follow still
	search mode when the
		Note
	time set with the STILL
		The Step setting is enabled only when “STILL TIMER” is set to
	TIMER menu item
	elapses.	less than 1 minute.

64 Menu Contents