ENGLISH / A-11

BEFORE EACH USE:

1Be sure you understand the operator controls and their function.

2Turn the Master Key Switch (A) ON (l) and check the Battery Condition Indicator (B). If the red light comes on, recharge the battery pack before using the machine

3Check that a new or clean pad has been installed.

4Check that a Dust Collection Bag (5) is installed.

PLAN YOUR FLOOR BURNISHING:

1Pre-sweep or scrub floor area of debris to prevent scratching and poor burnishing performance.

2Arrange long runs with a minimum of stopping or starting.

3Avoid bumping into posts or scraping the side of the machine.

OPERATING THE MACHINE

NOTE: Bold numbers or letters in parentheses indicate an item shown on pages A-6 – A-7.

Follow the instructions in PREPARING THE MACHINE FOR USE and the BEFORE EACH USE section of the manual.

1While seated on the machine adjust the Steering Wheel (11) using the Tilt Steering Wheel Adjuster (9), to a comfortable operating position.

2Turn the Master Key Switch (A) ON (l). This will display the Battery Condition Indicator Light(s) (B) and Hour Meter / Error Display (C).

3To transport the machine to the work area, apply even pressure on the front of the FWD/REV Drive Pedal (8) to go Forward or the rear of the pedal for Reverse. NOTE: The front drive wheel has a built in electromagnetic brake that engages whenever the FWD/REV Drive Pedal (8) is in the neutral position or when the Master Key Switch (A) is turned OFF. See the ELECTROMAGNETIC BRAKE section for manual over- ride instructions.

4Once at the work area, the pad pressure can be adjusted by turning the Master Key Switch (A) off. Hold down the Pad Drive Raise / Lower Switch (E) while turning on the Master Key Switch (A). The word “Adjust” will scroll on the Display (C) and the Pad Drive Raise/Lower Switch can be released. Once released, the display will read either “1”, “2”, or “3”. These are the pad pressure settings with “3” being the highest pad pressure setting. To change pad pressure, press the Pad Drive Raise / Lower Switch (E) to increment between 1, 2, and 3. Once you have selected the setting that you want to burnish with turn the Master Key Switch (A) off to store the setting in the memory. This setting will remain in the control panel’s memory until it is changed again using the above procedure.

5When at the work area press the machine’s FWD/REV Drive Pedal (8) to move the machine in either FWD or REV drive. The machine should always be moving before lowering the Pad Drive Deck (1).

6Once the machine is moving, lower the Pad Drive Deck (1) by pressing the Pad Drive Raise / Lower Switch (E). The Pad Drive Indicator Light (D) on the control panel will light yellow when going down and then turns green to confirm the lowered position and the pad begins to turn. To raise the Pad Drive Deck (1) press the Pad Drive Raise / Lower Switch (E). The Pad Drive Indicator Light (D) will be red when coming up and then turns OFF to confirm the raised position. NOTE: When the operator’s foot is removed from the Drive Pedal, the pedal automatically returns to neutral and the pad motor will shut off after about 1 second (the Pad Drive Indicator Light (D) will light yellow). Raise the Pad Drive Deck before stopping the machine. The floor may be damaged if the machine is stopped with the pad down and running.

7Begin burnishing making long straight line passes, overlap each pass 2-3 inches (5-7 cm). Adjust your machine speed according to the condition of the floor (if the floor is heavily scuffed, drive at a slower rate to ensure proper burnishing). The Active Dust Control Kit (21) if installed will be running whenever the Master Key Switch (A) is ON, the Pad Drive Deck (1) is down and the FWD/REV Drive Pedal (8) is off the neutral position.

CAUTION!

The floor may be damaged if travel of the machine is stopped with the pad down and running.

8It may become necessary when burnishing to stop the machine, raise the pad and check to see if the pad is loaded up with floor finish and dirt. If it is, turn the pad over to expose the clean side, or install a clean pad.

IMPORTANT NOTE: In the event a fast emergency shutdown of the unit is required push the Emergency Power Disconnect (10).

FORM NO. 56041634 - Advolution™ 2710 / UHR 70-1700 - A-11

Page 10 Page 12
Page 11
Image 11
Nilfisk-Advance America 56422000, 2710 English / A-11, Before Each USE, Plan Your Floor Burnishing, Operating the Machine
Page 10 Page 12

56422002, 56422001, 2710, 56422000, UHR 70-1700 specifications

The Nilfisk-Advance America UHR 70-1700 is a versatile and powerful cleaning machine specifically designed for various industrial and commercial applications. This high-performance unit is engineered to provide efficient and effective cleaning solutions, making it an essential tool for facilities where cleanliness and hygiene are paramount.

One of the standout features of the UHR 70-1700 is its robust suction power. Equipped with a high-efficiency motor, it offers superior suction capabilities that ensure thorough dirt and debris removal from a wide range of surfaces. Whether it's carpets, hard floors, or upholstery, this machine can adapt to meet diverse cleaning needs.

Another key technology incorporated into the UHR 70-1700 is the advanced filtration system. This system not only captures dirt and dust particles but also works to improve indoor air quality. The inclusion of HEPA filters helps trap allergens and finer particles, ensuring cleaner air is circulated throughout the environment, which is particularly beneficial for sensitive conditions.

The machine boasts an ergonomic design that enhances usability and operator comfort. With easy-to-reach controls, adjustable handles, and a lightweight body, the UHR 70-1700 can easily be maneuvered in tight spaces or around obstacles, making it suitable for various settings, from schools to hospitals and commercial offices.

Durability is another hallmark of the UHR 70-1700. Constructed with high-quality materials, this unit is built to withstand the rigors of continuous use in demanding environments. Its components are designed to reduce wear and tear, thereby extending the equipment's lifespan and ensuring long-term value for businesses.

The UHR 70-1700 offers flexible cleaning options with various attachments and accessories, allowing operators to customize their cleaning approach. From specialized brush heads for delicate surfaces to high-pressure nozzles for tough grime, the machine is adaptable to meet specific cleaning challenges.

Overall, the Nilfisk-Advance America UHR 70-1700 presents an exceptional blend of power, efficiency, and versatility. With its advanced technologies, user-friendly design, and robust construction, it stands out as a top choice for professionals seeking a reliable cleaning solution in a variety of settings. Whether for routine maintenance or deep cleaning tasks, this machine delivers quality performance time and time again.
Top Page Image Contents