§4.0 INSTALLATION

PLEASE READ CAREFULLY BEFORE BEGINNING INSTALLATION. FAILURE TO FOLLOW THESE PROCEDURES CAN RESULT IN DAMAGE TO YOUR SYSTEM AND VOID YOUR WARRANTY.

§4.1 LOCATION

It is recommended that systems be located where they are protected from harsh environments such as rain, snow and extreme temperatures (both hot and cold). MN-800 TF units can be located just about anywhere there is a water and electrical supply. This can be on the floor, mounted on the wall with a shelf, or any other flat surface. Keep in mind, however, that they should be out of normal traffic patterns and should be easily accessed for daily monitoring and service.

§4.2 SYSTEM PLUMBING INSTALLATION GUIDE LINES

A complete plumbing diagram of the system installation is shown in Figure 2. Always abide by local plumbing codes when installing the system. We recommend that a licensed plumbing contractor install this system. When installation procedures conflict with your local plumbing codes, STOP and contact Nimbus. This installation guide assumes the appropriate electrical outlet, 2 city water valves (1/2” FPT) and 1 valve (1/2” FPT) for distribution to the food service machines have been installed convenient to the system installation location. All threaded fittings are to be installed with Teflon tape.

IMPORTANT: FOR PLASTIC TUBING, USE ONLY SUPPLIED NYLON FERRULES AND BRASS TUBE INSERTS. DO NOT USE BRASS FERRULES ON PLASTIC TUBING.

§4.2.1 TANK PREPARATION AND INSTALLATION:

Install the 1-¼” x ¾” bushing In the 1-¼” FPT fitting at the bottom of the tank then install the ¾” MPT x 5/8” compression elbow in the bushing. Direct the 5/8” compression end toward the opening in the tank skirt. Cut a piece of black 5/8” tubing to extend about 4” beyond the tank skirt. Then install the tubing into the 5/8” compression fitting on the tank outlet.

Follow the instructions included with the tank wall brace kit to secure the tank to the rear wall. Locate the restraint brackets about 15” and 30” above the floor. Set the tank in place and rotate it so the bottom tank outlet is positioned as desired. Tighten the bracket clamps securely around the tank.

Remove the blue protective cap from the nut on top of the tank. Install the 5/8” x 1-½” long stud in the nut. Install the black plastic feet on the legs of the RO frame then lift and place the RO system on top of the tank with the threaded stud extending through the hole in the center of the RO frame base. Install the flat washer and nut on the stud. Rotate the RO so there is access to the 20” filters on the front of the unit. Tighten the 5/8” nut to secure the RO to the tank.

Install the ½” ball valve on the 5/8” tubing on the outlet of the tank. Use one straight and one elbow of ½” MPT x 5/8” compression fitting. With these fittings the valve can be installed straight out from the tank or pointing vertically up the side of the tank as desired. Connect a

8

Page 7 Page 9
Page 8
Image 8
Nimbus Water Systems MN-800-TF manual §4.0 Installation, §4.1 Location, §4.2 System Plumbing Installation Guide Lines
Page 7 Page 9

MN-800-TF specifications

The Nimbus Water Systems MN-800-TF is an innovative water filtration system designed to provide homes with clean, safe, and great-tasting water. Emerging as a leading solution in the water purification market, the MN-800-TF stands out due to its advanced features and cutting-edge technologies that cater to diverse filtration needs.

One of the main features of the MN-800-TF is its multi-stage filtration process, which includes a combination of sediment filters, activated carbon, and reverse osmosis membranes. This multi-tier approach ensures that a wide range of impurities such as chlorine, heavy metals, sediments, and even microorganisms are effectively removed from the water. This results in not only improved taste but also enhanced safety for household consumption.

The system utilizes advanced filtration technologies, including a high-capacity reverse osmosis membrane that boasts an impressive rejection rate for dissolved solids. This technology ensures that the water retains essential minerals while eliminating harmful contaminants. The activated carbon filters are designed to reduce chlorine levels and volatile organic compounds, resulting in water that is pure and refreshing.

In terms of user convenience, the MN-800-TF is equipped with an easy-to-read digital display that provides real-time information regarding filter status and water quality. The system also features a simple, intuitive setup process and space-saving design, making it suitable for both small and large homes. The compact design allows for installation under sinks or in utility rooms, optimizing space without compromising efficiency.

Another notable characteristic of the MN-800-TF is its sustainable approach. The system is designed to produce minimal wastewater during the filtration process, which is a critical consideration given the rising concern over water conservation. Moreover, by using a reusable filter system, users can reduce plastic waste generated from traditional bottled water usage.

The Nimbus Water Systems MN-800-TF is also backed by robust customer support and a warranty, ensuring peace of mind for users. Overall, this water filtration system integrates advanced technology and user-friendly features, making it an optimal choice for anyone looking to enhance their home’s water quality. With its combination of efficiency, sustainability, and reliability, the MN-800-TF truly embodies the future of home water purification.
Top Page Image Contents