piece of black 5/8” tubing from the valve up to the 5/8” compression fitting at the back right side of the RO system manifold.

§4.2.2 BY-PASS PANEL PREPARATION AND INSTALLATION:

The by-pass panel is to be located convenient to the RO where the TDS monitor is visible and the valve can be operated without difficulty.

The standard fittings provided are ½” MPT x 5/8” compression to be installed directly in the 3 ½” FPT ports at the bottom of the panel. Three ½” street elbows are also provided to allow the option of mounting the by-pass panel closer to a floor surface if desired.

Referring to the front view of the panel: the fitting marked FEED (Left side) will be connected to a city water valve, the fitting marked USAGE (center) will be connected to the valve feeding all food service machines, the fitting marked FROM RO (right Side) will be connected to the RO unit Post filter fitting marked FAUCET.

Two ½” MPT x 5/8” compression fittings are also provided for the 2 valves indicated above. Make all 3 connections using the 5/8” black tubing provided.

§4.2.3 RO FEED WATER CONNECTION:

A ½” MPT x 5/8” compression fitting is provided to connect a city water feed valve to the RO feed water filter inlet Marked FEED. Install the fitting in the valve and connect to the RO using the 5/8” black tubing provided.

§4.2.3 RO DRAIN CONNECTIONS:

3/8” white plastic tubing is used to connect the brine outlet to a drain and the product high pressure relief valve to drain. The fittings are the quick connect type and are marked DRAIN.

It is suggested the product high pressure relief valve be connected to drain via an air gap device (not supplied) so that any flow, although unlikely, would be diverted to drain. The opening of this valve and subsequent water flow is an indication of a system malfunction, most likely in the tank pressure switch.

§4.3 ELECTRICAL

A complete electrical diagram of the RO system is shown in Figure 3.

WARNING! THE SYSTEM MAY START WHEN POWER IS APPLIED. DO NOT CONNECT POWER UNTIL THE SYSTEM IS COMPLETELY INSTALLED AND READY TO RUN.

In the U.S., MN-800 TF systems come with a standard 115V three-prong plug. When wired for 220V, the systems have only bare leads for either hard wiring to a disconnect switch or for installation of the proper plug. Be sure the receptacle you use is on a circuit that has a Ground Fault Interrupter (GFI) and has sufficient capacity for the operating current as listed in §1.0 SYSTEMS SPECIFICATIONS. It is recommended that the unit be installed on a dedicated circuit to prevent overloading on system start-up. The power cord on the MN-800-TF is 10 feet long. The electrical outlet must be located accordingly.

10

Page 9 Page 11
Page 10
Image 10
Nimbus Water Systems MN-800-TF manual §4.2.2 BY-PASS Panel Preparation and Installation, §4.2.3 RO Feed Water Connection
Page 9 Page 11

MN-800-TF specifications

The Nimbus Water Systems MN-800-TF is an innovative water filtration system designed to provide homes with clean, safe, and great-tasting water. Emerging as a leading solution in the water purification market, the MN-800-TF stands out due to its advanced features and cutting-edge technologies that cater to diverse filtration needs.

One of the main features of the MN-800-TF is its multi-stage filtration process, which includes a combination of sediment filters, activated carbon, and reverse osmosis membranes. This multi-tier approach ensures that a wide range of impurities such as chlorine, heavy metals, sediments, and even microorganisms are effectively removed from the water. This results in not only improved taste but also enhanced safety for household consumption.

The system utilizes advanced filtration technologies, including a high-capacity reverse osmosis membrane that boasts an impressive rejection rate for dissolved solids. This technology ensures that the water retains essential minerals while eliminating harmful contaminants. The activated carbon filters are designed to reduce chlorine levels and volatile organic compounds, resulting in water that is pure and refreshing.

In terms of user convenience, the MN-800-TF is equipped with an easy-to-read digital display that provides real-time information regarding filter status and water quality. The system also features a simple, intuitive setup process and space-saving design, making it suitable for both small and large homes. The compact design allows for installation under sinks or in utility rooms, optimizing space without compromising efficiency.

Another notable characteristic of the MN-800-TF is its sustainable approach. The system is designed to produce minimal wastewater during the filtration process, which is a critical consideration given the rising concern over water conservation. Moreover, by using a reusable filter system, users can reduce plastic waste generated from traditional bottled water usage.

The Nimbus Water Systems MN-800-TF is also backed by robust customer support and a warranty, ensuring peace of mind for users. Overall, this water filtration system integrates advanced technology and user-friendly features, making it an optimal choice for anyone looking to enhance their home’s water quality. With its combination of efficiency, sustainability, and reliability, the MN-800-TF truly embodies the future of home water purification.
Top Page Image Contents