Installation Menu | Vidikron 140/150 guide

Installation

previously (refer to Unlocking Channels on page 49), unlock the next channel and repeat the calibration procedure. Do this for each of the remaining channels.

Select Installation from the Vision 140/150 Main Menu to access these advanced lamp and lens configuration options:

•LumaCal™, for maintaining constant lamp brightness

•OptiCal™, to save and restore lens positions

Calibration and Test Patterns – LumaCal (Lamp Calibration): LumaCal defines the range of power needed to maintain lamp brightness over time.

For best results, allow the projector to warm up for 15 minutes prior to

Note	using LumaCal.

To use LumaCal:

1.Select Installation from the Main Menu.

2.Select Calibration and Test Patterns from the Installation Menu.

3.Select LumaCal from the Calibration and Test Patterns Menu.

4.Select Calibrate LumaCal to calibrate the lamp using your projector's unique specifications (recommended). Or, select Use Default Settings to undo the effects of a previous calibration.

In the event of a power failure, the projector reverts to the default LumaCal settings in which case you should re-calibrate the lamp.

LumaCal lamp calibration takes approximately two minutes.

Note

Installation Menu

	Installation
1.	Language	English
2.	Picture Orientation	Front

3.Reserved

4.Auto Power Up

5.Set Date and Time

6.OSD Adjust

7.IR and Serial Adjust

8.Geometry and Color

9.Calibration and Test Patterns

0.Service Mode Option 1 Card: Empty Option 2 Card: Empty

Calibration and Test Patterns

1.	Test Patterns	Grid
2.	Test Pattern Level	512

3.Freeze Image

4.

Color Enable

White

5.Odd Pixel Adjustment

6.Reserved

7.Clipping Detector

8.Level Detector

9.

Level Value

512

0.Aspect Ratio Overlay

LumaCal Calibrate LumaCal

OptiCal Full

Automatic Lens Calibration

Vision Model 140/150 Owner’s Operating Manual

57

Image 69

Vidikron 140/150 manual LumaCal lamp calibration takes approximately two minutes, Installation Menu

Contents

140/150 Page For Projectors, Video Processors and Controllers TWO Year Limited Warranty Effective Warranty Date Vidikron Safety Precautions 1Table of Contents Viii Specifications Maintenance and TroubleshootingOperation Serial Communications Table of Contents 1List of Figures List of Figures Carriage return must be used after each command or string About This ManualThis Manual They also provide supplemental information Using This ManualPerformance or cause a malfunction If you need Turn to Description, Features and Benefits Optional Accessories Vision 140/150 Top/Rear/Front View Vision 140/150 at a Glance TOP IR Sensor BUILT-IN Keypad Adjustable FeetInput Panel LED Status Display Remote Vision 140/150 Input PanelEthernet Input 1 Rgbhv Vision 140/150 Rear-Panel Keypad Left Button UP ButtonDown Button Right Button VHD Controller Front Panel IR SensorVacuum Fluorescent Display Hdmi OUT VHD Controller Rear PanelInputs Composite Video Input Main Power Switch Power Input 100 to 240 VACRS-232 Control Port Main AC Fuse VHD Controller/Vision 140/150 Remote Control Vision 140/150 Remote Control Unit IR Output Indicator LightRETURN/EXIT Cinema ISF DAY Controls and Functions Remote Control To install batteries in the remote controlOperation Installation Quick Setup Installation OverviewStep Procedure For Details, Refer to Projector Installation Options Installation ConsiderationsInstallation Type Advantages Considerations Throw Ratio Vision 140/150 Lens Options and Throw RatiosWith 126.9x54-inch Screen Floor Installation Ceiling InstallationPosition Vertical and Horizontal Lens Horizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Folded Optics Lens Assembly Front View Installing the Projection Lens Anamorphic lens mounting kit is partially pre-assembled at Installing the Optional CineWide Lens Mount Lens motor installed Ceiling-mounting an AutoScope-equipped projectorFloor-Mount Mounting the Vision 140/150 Adjusting the ProjectionFloor Mounting Upright Angle Connecting the VHD Connections to the Vision 140/150 and VHD Controller140/150 Connecting Source Hdmi Connections See FigureController 11. Digital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See Figure Personal Computer Analog Computer RGB Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See Figure 14. RS-232 Control System Connection Connection Equipment Connecting 12-Volt Trigger Connecting an External IR Receiver to the VHD Controller Power sourceProjector Component SD Ntsc 480i 169 V150 Turning on the Power Focus Zoom Vertical and Horizontal Lens Shift Adjusting the Picture Orientation Primary Lens Adjustments Plate fixed CineWide Installing and Adjusting the CineWide Anamorphic Lens Horizontal Position X Adjustment Installation Geometry Anamorphic Lens Top View Wrong Position Calibrating Projector Input 2 DVI Main 17. TheaterMaster Remote Control for Vision 140/150 Control Functions Navigating the Projector Disabled 16x9 night Vhd 720p4x3 night Ltrbox night Number Sync 26.97 kHz Input 23.98 Hz Menu Name 16x9 nightAuto Source Locked Previous Channel Next Channel Interlace Native aspect ratio is with the primary lens only. With an SupportSize and Position Menu Installation Picture Quality Menu Adjust Pixel Tracking before Pixel Phase White Balance Uncheck this item before exiting this menu There must be at least two consecutive white pixels present Each setting Back Porch Clipping Detector Color Enable Red LumaCal lamp calibration takes approximately two minutes Installation Menu Above, the Automatic Lens Calibration setting has no effect Factors Working With the Lamp Value only 1246 may represent 3500 lumens, for example RVR Easily maintained as the lamp ages Installation 4Operation Using the On-Screen Menus Service ISF PresetsInput Source Aspect Ratio Main Menu Input SourceAspect Ratio Description Aspect Ratio Settings169 Hdtv programs in their With a 2.351 screen and a Remote Picture Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Typical Test Pattern for Adjusting Sharpness Information ISF Presets Calibration You must enter a passcode to access the Calibration menuShould be used by ISF-certified technicians only ISF Night Operation Service You must enter a passcode to access the Service menuDo not change the Type setting in this menu Keystone Correction Vertical Keystone Correction HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Lamp cover 2 screws Lamp and Filter Replacement Removing the Lamp RVR Removing the Primary Lens Lens Replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Trigger CineWide with Symptom Vision 140/150 Error Codes Description GeneralLamp Failures Code Description Power and Cooling Code Description Code Description Miscellaneous RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands Multiple serial commands Aspect Ratio Commands Image Preset Commands Output Shift Commands Command Value Stored? Description Miscellaneous CommandsEnter key Serial Communications Vision 140/150 Specifications Vision 140/150 Specifications Industry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements Vision Dimensions VHD Controller Specifications Vision 140/150 Dimensions Vision 140/150 DimensionsPage Vidikron