Code Description | Vidikron 140/150 instruction

Maintenance and Troubleshooting

Table 5-2. Vision 140/150 Error Codes (continued)

Code	Description

	TIPM (Image Processor)

60	Boot code CRC failed.

61	Unable to program DigMux PLD.

62	Unable to program Control PLD.

63	Unable to program Bubks PLD.

64	Unrecognized ROM type.

65	Write to flash ROM failed.

66	TIPM failure.

67	Downloaded code will not fit.

68	Scaler communication problem.

	Built-In Keypad

70	Unable to access EEPROM on the built-in keypad.

71	EEPROM memory re-initialization on the built-in keypad.

	Panel Driver and Formatter

80	Unrecognized Panel Driver.

81	Unable to program device on Panel Driver.

82	TI flash download failure.

83	TI flash download failure.

84	TI flash download failure.

85	TI-I2C write failure.

86	One or more formatters not responding; probable formatter software fault.

87	Formatter reports RDRAM failure.

88	Red modular Formatter communication failure.

89	Green modular Formatter communication failure.

8A	Blue modular Formatter communication failure.

93	Modular formatter architecture error.

94	Modular formatter DMD mismatch.

95	Modular formatter sequence mismatch.

Note: To clear a system error, press the EXIT key (on the projector’s rear-panel keypad) twice. If necessary, reset the projector by powering it off, allowing it to cool and powering it on again. Contact your Vidikron dealer or Vidikron technical support if the error persists.

Vision Model 140/150 Owner’s Operating Manual

89

Image 101

Vidikron 140/150 manual Code Description

Contents

140/150 Page For Projectors, Video Processors and Controllers TWO Year Limited Warranty Effective Warranty Date Vidikron Safety Precautions 1Table of Contents Viii Specifications Maintenance and TroubleshootingOperation Serial Communications Table of Contents 1List of Figures List of Figures This Manual Carriage return must be used after each command or stringAbout This Manual They also provide supplemental information Using This ManualPerformance or cause a malfunction If you need Turn to Description, Features and Benefits Optional Accessories Vision 140/150 Top/Rear/Front View Vision 140/150 at a Glance TOP IR Sensor BUILT-IN Keypad Adjustable FeetInput Panel LED Status Display Remote Vision 140/150 Input PanelEthernet Input 1 Rgbhv Vision 140/150 Rear-Panel Keypad Left Button UP ButtonDown Button Right Button Vacuum Fluorescent Display VHD Controller Front PanelIR Sensor Hdmi OUT VHD Controller Rear PanelInputs Composite Video Input Main Power Switch Power Input 100 to 240 VACRS-232 Control Port Main AC Fuse VHD Controller/Vision 140/150 Remote Control Vision 140/150 Remote Control Unit RETURN/EXIT IR Output IndicatorLight Cinema ISF DAY Controls and Functions Operation Remote ControlTo install batteries in the remote control Installation Step Procedure For Details, Refer to Quick SetupInstallation Overview Projector Installation Options Installation ConsiderationsInstallation Type Advantages Considerations Throw Ratio Vision 140/150 Lens Options and Throw RatiosWith 126.9x54-inch Screen Floor Installation Ceiling InstallationPosition Vertical and Horizontal Lens Horizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Folded Optics Lens Assembly Front View Installing the Projection Lens Anamorphic lens mounting kit is partially pre-assembled at Installing the Optional CineWide Lens Mount Floor-Mount Lens motor installedCeiling-mounting an AutoScope-equipped projector Mounting the Vision 140/150 Adjusting the ProjectionFloor Mounting Upright Angle 140/150 Connecting the VHDConnections to the Vision 140/150 and VHD Controller Controller Connecting SourceHdmi Connections See Figure 11. Digital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See Figure Personal Computer Analog Computer RGB Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See Figure 14. RS-232 Control System Connection Connection Equipment Connecting 12-Volt Trigger Projector Connecting an External IR Receiver to the VHD ControllerPower source Component SD Ntsc 480i 169 V150 Turning on the Power Focus Zoom Vertical and Horizontal Lens Shift Adjusting the Picture Orientation Primary Lens Adjustments Plate fixed CineWide Installing and Adjusting the CineWide Anamorphic Lens Horizontal Position X Adjustment Installation Geometry Anamorphic Lens Top View Wrong Position Calibrating Projector Input 2 DVI Main 17. TheaterMaster Remote Control for Vision 140/150 Control Functions Navigating the Projector Disabled 16x9 night Vhd 720p4x3 night Ltrbox night Number Sync 26.97 kHz Input 23.98 Hz Menu Name 16x9 nightAuto Source Locked Previous Channel Next Channel Interlace Size and Position Menu Native aspect ratio is with the primary lens only. With anSupport Installation Picture Quality Menu Adjust Pixel Tracking before Pixel Phase White Balance Uncheck this item before exiting this menu There must be at least two consecutive white pixels present Each setting Back Porch Clipping Detector Color Enable Red LumaCal lamp calibration takes approximately two minutes Installation Menu Above, the Automatic Lens Calibration setting has no effect Factors Working With the Lamp Value only 1246 may represent 3500 lumens, for example RVR Easily maintained as the lamp ages Installation 4Operation Using the On-Screen Menus Service ISF PresetsInput Source Aspect Ratio Aspect Ratio Main MenuInput Source Description Aspect Ratio Settings169 Hdtv programs in their With a 2.351 screen and a Remote Picture Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Typical Test Pattern for Adjusting Sharpness Information ISF Presets Calibration You must enter a passcode to access the Calibration menuShould be used by ISF-certified technicians only ISF Night Operation Do not change the Type setting in this menu ServiceYou must enter a passcode to access the Service menu Keystone Correction Vertical Keystone Correction HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Lamp cover 2 screws Lamp and Filter Replacement Removing the Lamp RVR Removing the Primary Lens Lens Replacement Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Trigger CineWide with Symptom Lamp Failures Vision 140/150 Error CodesDescription General Code Description Power and Cooling Code Description Code Description Miscellaneous RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands Multiple serial commands Aspect Ratio Commands Image Preset Commands Output Shift Commands Enter key CommandValue Stored? Description Miscellaneous Commands Serial Communications Vision 140/150 Specifications Vision 140/150 Specifications Industry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements Vision Dimensions VHD Controller Specifications Vision 140/150 Dimensions Vision 140/150 DimensionsPage Vidikron