Code Description Power and Cooling | Vidikron 140/150 manual

Maintenance and Troubleshooting

Table 5-2. Vision 140/150 Error Codes (continued)

Code	Description

	Power and Cooling

46	Red DMD heat sink overheated.

47	Green DMD heat sink overheated.

48	Blue DMD heat sink overheated.

49	Prism overheated.

4C	Projector shutdown due to critical error.

C0	Lamp blower failure (lamp not turned on).

51	LVPS fan failed (Fan 1).

52	LVPS/Red cooling fan failed (Fan 2).

53	DC lamp fan failed (Vision 140; Fan 3).

54	Red DMD heatsink fan failed (Fan 4).

55	Green DMD heatsink fan failed (Fan 5).

56	Blue DMD heatsink fan failed (Fan 6).

57	TIPM fan failed (Fan 7).

58	TIPM fan failed (Fan 8).

Note: To clear a system error, press the EXIT key (on the projector’s rear-panel keypad) twice. If necessary, reset the projector by powering it off, allowing it to cool and powering it on again. Contact your Vidikron dealer or Vidikron technical support if the error persists.

88	Vision Model 140/150 Owner’s Operating Manual

Image 100

Vidikron 140/150 manual Code Description Power and Cooling

Contents

140/150 Page TWO Year Limited Warranty For Projectors, Video Processors and Controllers Effective Warranty Date Vidikron Safety Precautions 1Table of Contents Viii Maintenance and Troubleshooting SpecificationsOperation Serial Communications Table of Contents 1List of Figures List of Figures About This Manual Carriage return must be used after each command or stringThis Manual Using This Manual They also provide supplemental informationPerformance or cause a malfunction If you need Turn to Description, Features and Benefits Optional Accessories Vision 140/150 at a Glance Vision 140/150 Top/Rear/Front View Adjustable Feet TOP IR Sensor BUILT-IN KeypadInput Panel LED Status Display Vision 140/150 Input Panel RemoteEthernet Input 1 Rgbhv Vision 140/150 Rear-Panel Keypad UP Button Left ButtonDown Button Right Button IR Sensor VHD Controller Front PanelVacuum Fluorescent Display VHD Controller Rear Panel Hdmi OUTInputs Composite Video Input Power Input 100 to 240 VAC Main Power SwitchRS-232 Control Port Main AC Fuse Vision 140/150 Remote Control Unit VHD Controller/Vision 140/150 Remote Control Light IR Output IndicatorRETURN/EXIT ISF DAY Cinema Controls and Functions To install batteries in the remote control Remote ControlOperation Installation Installation Overview Quick SetupStep Procedure For Details, Refer to Installation Considerations Projector Installation OptionsInstallation Type Advantages Considerations Vision 140/150 Lens Options and Throw Ratios Throw RatioWith 126.9x54-inch Screen Ceiling Installation Floor InstallationPosition Vertical and Horizontal Lens Horizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Folded Optics Installing the Projection Lens Lens Assembly Front View Installing the Optional CineWide Lens Mount Anamorphic lens mounting kit is partially pre-assembled at Ceiling-mounting an AutoScope-equipped projector Lens motor installedFloor-Mount Adjusting the Projection Mounting the Vision 140/150Floor Mounting Upright Angle Connections to the Vision 140/150 and VHD Controller Connecting the VHD140/150 Hdmi Connections See Figure Connecting SourceController Digital DTV RGB or Component Video Connections See Figure 11. Digital DTV RGB or Component Video Connections Analog Computer RGB Connections See Figure Personal Computer Composite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etc Connection 14. RS-232 Control System Connection Connecting 12-Volt Trigger Equipment Power source Connecting an External IR Receiver to the VHD ControllerProjector Turning on the Power Component SD Ntsc 480i 169 V150 Adjusting the Picture Orientation Primary Lens Adjustments Focus Zoom Vertical and Horizontal Lens Shift Installing and Adjusting the CineWide Anamorphic Lens Plate fixed CineWide Horizontal Position X Adjustment Installation Anamorphic Lens Top View Geometry Wrong Position Calibrating Projector Input 2 DVI 17. TheaterMaster Remote Control for Vision 140/150 Main Control Functions Disabled Navigating the Projector Vhd 720p 16x9 night4x3 night Ltrbox night Name 16x9 night Number Sync 26.97 kHz Input 23.98 Hz MenuAuto Source Locked Previous Channel Next Channel Interlace Support Native aspect ratio is with the primary lens only. With anSize and Position Menu Installation Adjust Pixel Tracking before Pixel Phase Picture Quality Menu White Balance There must be at least two consecutive white pixels present Uncheck this item before exiting this menu Back Porch Clipping Detector Color Enable Red Each setting Installation Menu LumaCal lamp calibration takes approximately two minutes Above, the Automatic Lens Calibration setting has no effect Working With the Lamp Factors Value only 1246 may represent 3500 lumens, for example Easily maintained as the lamp ages RVR Installation Using the On-Screen Menus 4Operation ISF Presets ServiceInput Source Aspect Ratio Input Source Main MenuAspect Ratio Aspect Ratio Settings Description169 Hdtv programs in their Remote With a 2.351 screen and a Perform the adjustments in the order listed here Picture Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position ISF Presets Information You must enter a passcode to access the Calibration menu CalibrationShould be used by ISF-certified technicians only ISF Night Operation You must enter a passcode to access the Service menu ServiceDo not change the Type setting in this menu Vertical Keystone Correction Keystone Correction HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Lamp and Filter Replacement Lamp cover 2 screws Removing the Lamp RVR Lens Replacement Removing the Primary Lens Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Symptom Trigger CineWide with Description General Vision 140/150 Error CodesLamp Failures Code Description Power and Cooling Code Description Code Description Miscellaneous Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands Multiple serial commands Aspect Ratio Commands Image Preset Commands Output Shift Commands Value Stored? Description Miscellaneous Commands CommandEnter key Serial Communications Vision 140/150 Specifications Vision 140/150 Specifications Home Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements Vision Dimensions VHD Controller Specifications Vision 140/150 Dimensions Vision 140/150 DimensionsPage Vidikron