PART | R0802A |
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the centre of this manual.
Key No. | Qty. | Description | Key No. | Qty. | Description |
1 | 1 | Allen Wrench | 51 | 1 | Motor Isolator |
2 | 2 | Wheel Bolt | 52 | 1 | Incline Motor Bolt (Top) |
3 | 1 | Rear Endcap (Left) | 53 | 8 | Endcap Washer |
4 | 1 | Grounding Nut | 54 | 1 | Incline Motor Stop |
5 | 2 | Rear Roller Adj. Screw | 55 | 8 | Endcap Nut |
6 | 2 | Rear Wheel | 56 | 1 | Incline Motor Bolt (Bottom) |
7 | 8 | Front Wheel Nut/Frame Pivot Nut | 57 | 1 | Incline Motor |
8 | 8 | Endcap Screw | 58 | 1 | Front Roller Bolt |
9 | 1 | Roller Guard (Left) | 59 | 4 | Plastic |
10 | 1 | Roller Guard (Right) | 60 | 1 | Electronic Plate |
11 | 1 | Rear Endcap (Right) | 61 | 1 | Controller |
12 | 1 | Roller Ground Wire | 62 | 1 | Motor Controller Wire |
13 | 2 | Motor Bolt | 63 | 1 | Power Cord Set |
14 | 1 | Rear Roller | 64 | 1 | Ferrite Box |
15 | 1 | Warning Decal | 65 | 1 | On/Off Switch |
16 | 1 | Latch Plate | 66 | 4 | Belly Pan Screw (Long) |
17 | 1 | Idler Arm Bolt | 67 | 1 | Audio Wire Nut |
18 | 2 | Frame Pivot Bolt | 68 | 1 | Circuit Breaker |
19 | 1 | Front Endcap (Left) | 69 | 2 | Static Decal |
20 | 2 | Belt Guide | 70 | 1 | 12” Audio Wire |
21 | 1 | Foot Grip (Left) | 71 | 1 | Belly Pan |
22 | 1 | Walking Belt | 72 | 4 | 3/4” Screw |
23 | 1 | Walking Deck | 73 | 2 | Rear Adj. Lock Washer |
24 | 1 | Foot Grip (Right) | 74 | 2 | Rear Adj. Spring |
25 | 1 | Power Board | 75 | 1 | Tension Washer |
26 | 1 | Front Endcap (Right) | 76 | 1 | Console Base |
27 | 4 | Support Bracket Screw | 77 | 1 | Book Holder |
28 | 1 | Support Bracket | 78 | 1 | Console |
29 | 1 | Front Roller/Pulley | 79 | 2 | Handrail Endcap |
30 | 1 | Magnet | 80 | 2 | Pulse Grip |
31 | 6 | Console Screw (Long) | 81 | 4 | Pulse Grip Screw |
32 | 4 | Frame Pivot Washer | 82 | 10 | Short Console Screw |
33 | 2 | Frame Pivot Bushing | 83 | 1 | Console Back |
34 | 2 | Frame Pivot Spacer | 84* | 2 | Extension Leg Assembly |
35 | 1 | Reed Switch | 85 | 2 | Extension Leg Endcap |
36 | 1 | Reed Switch Clip | 86 | 8 | Base Screw |
37 | 1 | Tension Bolt | 87 | 2 | Incline Motor Spacer |
38* | 1 | Idler Assembly | 88 | 2 | Extension Leg |
39 | 1 | Idler Arm | 89 | 1 | Handrail |
40 | 1 | Motor Belt | 90 | 7 | Base Pad |
41 | 1 | Pulley Spacer | 91 | 1 | Motor Hood |
42 | 3 | Lift Frame Nut | 92 | 1 | 8” Wire Tie |
43 | 1 | Idler Pulley | 93 | 2 | Cable Tie Clamp |
44 | 1 | Lift Frame Bushing | 94 | 2 | Clamp Screw |
45 | 1 | Idler Spring | 95 | 1 | Releasable Tie |
46 | 1 | Motor | 96 | 2 | Lift Pivot Bolt |
47 | 1 | Lift Frame | 97 | 2 | Front Wheel Bolt |
48 | 2 | Motor Mount Bushing | 98 | 2 | Front Wheel |
49 | 10 | Screw | 99 | 1 | Incline Motor Guard |
50 | 1 | Jack | 100 | 1 | Upright Grommet |
30
