4. Set the Right Upright Spacer (79) on the Base | 4 |
|
|
|
(83). Be careful not to pinch the Upright Wire |
|
|
| |
|
| 6 |
| |
(38). With the help of a second person, insert |
|
|
| |
two 3/8” x 5” Bolts (6) with two 3/8" Star |
|
|
| 77 |
Washers (9) into the Right Upright (78) and set | 78 |
|
| |
|
|
| ||
the Right Upright into the Right Upright Spacer. |
|
|
| |
79 | 9 |
| ||
If necessary, use a rubber mallet on top of the |
| |||
|
|
| ||
Right Upright to make sure that the Upright is |
|
|
|
|
fully inserted into Spacer. |
|
|
|
|
Partially tighten the 3/8” x 5” Bolts (6) by turning |
|
|
| 38 |
them several times; do not fully tighten the |
|
|
| |
|
|
|
| |
Bolts yet. |
|
|
|
|
Press a Base Endcap (77) into the Base (83). | 83 |
|
|
|
|
|
|
| |
5. With the help of a second person, carefully tip | 5 |
|
|
|
the treadmill onto its right side. Partially fold the |
|
|
| |
|
|
|
| |
Frame (56) so that the treadmill is more stable; | A |
|
| B |
do not fully fold the Frame yet. |
|
| ||
|
|
|
| |
Remove and discard the two indicated bolts (A) |
|
|
| 83 |
and the shipping bracket (B). | 81 |
|
| |
|
|
| 56 | |
Attach a Base Pad (81) to the Base (83) in the |
|
|
| |
|
|
|
| |
location shown with a #8 x 1" Tek Screw (2) and | 2 |
|
| 113 |
a Base Pad Spacer (13). Then, attach another |
|
|
| |
|
|
|
| |
Base Pad (81) with only a #8 x 1" Tek Screw (2). |
|
| 13 |
|
|
|
|
| |
Remove the 3/8" Nut (8), the 3/8" x 2" Shoulder |
|
|
| 84 |
Bolt (113), and the shipping bracket (C) from the |
|
|
| |
Base (83). Attach a Wheel (84) with the Bolt and |
|
| 2 | 81 |
the Nut that you just removed. Do not over- |
|
| C | |
|
|
| ||
tighten the Nut; the Wheel must turn freely. |
|
|
| 8 |
Discard the shipping bracket. |
|
|
|
|
6. Set the Left Upright Spacer (76) on the Base | 6 |
|
|
|
(83). With the help of a second person, insert |
|
|
| |
77 |
|
|
| |
two 3/8” x 5” Bolts (6) with two 3/8" Star | 6 |
| 74 | |
Washers (9) into the Left Upright (74) and set |
|
|
| |
|
|
|
| |
the Left Upright into the Left Upright Spacer. If |
| 9 |
| 76 |
necessary, use a rubber mallet on top of the Left |
|
|
| |
|
|
|
| |
Upright to make sure that the Upright is fully in- |
|
|
|
|
serted into the Left Upright Spacer. |
|
|
|
|
Partially tighten the 3/8” x 5” Bolts (6) by turning |
|
|
|
|
them several times; do not fully tighten the |
|
|
|
|
Bolts yet. |
|
|
|
|
Press a Base Endcap (77) into the Base (83). |
|
|
| 83 |
|
|
|
| |
With the help of a second person, tip the tread- |
|
|
|
|
mill so that the Base (83) is flat on the floor. |
|
|
|
|
| 8 |
|
|
|
