4. See drawing 4a. While another person holds the | 4a |
|
|
|
Handrails (83), thread Handrail Bolts (104) two to three |
|
|
| |
|
|
|
| |
turns into the indicated holes in each Handrail. Then, re- |
| 83 |
|
|
move the Handrail Bolts. |
|
|
|
|
See drawing 4b. Pinch the tabs on the Grounding Bracket |
|
|
|
|
(115) so that the tabs will fit into the indicated hole in the |
|
|
| 104 |
left Upright (99). Then, insert the Grounding Bracket into |
|
|
|
|
the hole as far as possible. | 4b |
|
|
|
| 115 |
|
| |
Note: It may be helpful to set the Handrails (83) on the |
|
| 99 | |
|
|
| ||
Uprights (99) and loosely thread a Handrail Bolt (104) |
|
|
| 104 |
into the left Upright and the left Handrail. Tip the |
|
|
| |
|
|
|
| |
Handrails, if necessary, to thread in the Bolt. Have an- |
|
|
|
|
other person support the Handrails while you complete |
|
|
|
|
the remaining steps. |
|
|
|
|
5. Pull the Upright Wire Harness (119) up through a | 5 |
|
| A |
Handrail Spacer (116). Place the Handrail Spacer on the |
|
| ||
| 80 |
| Cutout | |
right Upright (99) as shown, with the cutout toward the |
|
| ||
|
|
| ||
treadmill (see inset drawing A). |
|
|
| 116 |
|
|
| 83 | |
Connect the Upright Wire Harness (119) to the wires ex- |
|
|
| |
|
|
| 99 | |
tending from the Console Base (80). The connectors |
|
|
| |
should slide easily and “snap” into place. If the con- |
| 119 | 99 | B 119 |
nectors do not slide easily and snap into place, turn a |
|
| ||
|
|
|
| |
connector and try again. Insert the connectors and the |
|
|
|
|
Upright Wire Harness into the hole in the Console Base |
|
|
|
|
(see inset drawing B). |
|
|
|
|
|
| 116 |
|
|
Set the Handrail (83) on the Handrail Spacer (116), being |
|
|
| 80 |
careful not to pinch the Upright Wire Harness (119). |
|
|
| |
|
|
|
| |
6. Insert two Handrail Bolts (104) with Handrail Washers | 6 |
|
| 83 |
(105) and Handrail Bushings (106) into the right Upright |
|
| ||
|
|
| ||
|
|
|
| |
(99) and the right Handrail Spacer (116). Turn the |
|
|
| 116 |
Handrail Bushings so they fit against the Upright (see the |
|
|
| |
|
| 83 | 115 | |
inset drawing). Lift the right Handrail (83) slightly and |
|
| ||
|
|
|
| |
align the Bolts with the holes in the Handrail. Loosely |
|
| 118 |
|
thread the Bolts into the Handrail. Do not tighten the |
|
|
| 104 |
Bolts yet. |
|
| 99 | |
|
|
| ||
See the inset drawing. Remove the Handrail Bolt (104) | 116 |
| 106 | |
|
|
| 105 | |
used in step 4. Place the other Handrail Spacer (116) on |
|
|
| |
|
|
|
| |
the left Upright (99), with the cutout toward the treadmill. |
|
|
|
|
Reach inside the left Upright and spread the tabs on the |
|
|
|
|
Grounding Bracket (115) to allow a Bolt to pass through |
| 106 |
|
|
the Grounding Bracket. Attach the left Handrail (83) as de- |
| 105 | 104 | |
scribed above. Make sure that the Handrail Bushings |
|
|
|
|
(106) are turned properly and that the Bolt goes through |
|
|
|
|
the Grounding Bracket. Tighten all four Handrail Bolts. |
|
|
|
|
Press an Upright Endcap (118) into each Upright. |
|
|
|
|
7. Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen | ||||
wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 27). To protect the | ||||
floor or carpet from damage, place a mat under the treadmill. |
|
|
| |
7
