4.PlaceoneoftheHandrailSpacers(65)ontheright Upright(69)asshown,withthecutouttowardthetread- mill(seeinsetdrawingA).PulltheUprightWireHarness

(98)upthroughtheHandrailSpacerPlacetheother. HandrailSpaceron theleftUpright(notshown).

HaveasecondpersonholdtheHandrails(66)nearthe

Uprights(69)asshown.ConnecttheUprightWire

Harness(98)tothewiresextendingfromtheConsole

Base(81).InserttheconnectorsandtheWireHarness (98)intotheholein theConsoleBase(81)(seeinset drawingB).

65

BeingcarefulnottopinchtheWireHarness(98),setthe Handrails(66)ontheSpacers(65).

5.InserttwoHandrailBushings(75)intotherightUpright (69).TurntheHandrailBushingssotheyfit againstthe

UprightwiththethicksidesoftheBushingsfacingthe centerofthetreadmillasshownin theinsetdrawing.

InserttwoHandrailBolts(78)withHandrailWashers

(77)intotheHandrailBushings(75),therightUpright (69),andtherightHandrailSpacer(65).Lifttheright

Handrail(66)toaligntheBoltswiththeholesin the HandrailNext,threadtheBoltsintotheHandrail.Do.

not tighten the Bolts yet.

Attach the left Handrail (not shown) in the same way. Tighten all four Handrail Bolts (78).

81

_- 77 Thick

,Side

75

7778

6.Make sure that all parts are tightened before you use the treadmill. Note: If there is a thin sheet of clear plastic on the face of the hood decal and the "ComforTrack" decal, remove it. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 27). To protect the floor or car- pet from damage, place a mat under the treadmill.

If you purchase the optional chest pulse sensor (see

 

 

 

88

page 24), follow

the steps below to install the receiver

 

 

 

 

 

[]

 

included with the chest pulse sensor.

 

 

 

 

1.

Make sure that the power cord is unplugged. Remove

 

 

 

 

 

the indicated Screws from the Console Back (88).

 

 

 

 

 

Important: The Screws may be different lengths. Keep

 

 

 

 

 

track of which Screws were removed from which holes.

 

 

 

 

2.

See drawing

2a. Peel the paper off the pad on the bottom

 

 

 

 

 

of the Receiver (A). Turn the Receiver so the cylinder is

 

 

 

 

 

on the side shown, and press the Receiver into the bot-

2a

81

2b

82

 

 

 

 

tom of the Console Base (81) in the indicated location.

 

 

 

/

 

See drawing 2b. Connect the Short Jumper Wire (B) to

 

 

 

PULSE

 

the wire on the Receiver (A). Connect the other end of

 

 

 

 

 

 

 

 

 

the Jumper Wire to the PULSE jack on the back of the

 

 

 

 

 

Console (82). Note: The included Long Jumper Wire and

 

 

 

 

 

Wire Tie are not needed and can be discarded.

 

 

 

 

 

Make sure that no wires are pinched. See step 1 above.

 

 

 

 

 

Reattach the Console (82) with the Screws. Note: If the

 

 

 

 

 

Screws are not put in the correct locations, the

 

 

 

 

 

Console will

be damaged.

 

 

 

 

Page 7
Image 7
NordicTrack NTTL11994 user manual InserttwoHandrailBolts78withHandrailWashers, Not tighten the Bolts yet