NuTone installation instructions Bathroom Ventilator, MODEL F305C, Insta Llation Instructions

INSTALLATION INSTRUCTIONS READ & SAVE THESE INSTRUCTIONS!

Bathroom Ventilator

WIRING INSTRUCTIONS

MODEL: F305C

IMPORTANT SAFETY INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF FIRE. ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.

B. Before servicing or cleaning unit, switch power off at service panel and lock service panel to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

LIGHT RECEP

WHITE

FAN LIGHT

RECEP RECEP

SWITCH

SWITCH

BLACK BLACK

FAN

RECEP

SWITCH

WHITE

CAUTION:

For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

INSTA LLATION INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

B. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer's guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

C. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

D. Ducted fans must always be vented to the outdoors.

E. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

F. NEVER place a switch where it can be reached from a tub or shower.

•MINIMUM CLEARANCE IN CEILING 53⁄8".

•For ceiling installation only.

•WARNING: To reduce the risk of fire or electrical shock, do not use this fan with any solid state speed control device.

•Installation must be inaccordance with local and national electrical codes.

•Not for use in kitchens.

•For installation in sloped ceilings up to 7/12 pitch.

•Ductwork must point up.

WIRING INSTRUCTIONS

1 . Remove both grille-reflector-socket assembly and motor-blade assembly from housing and set aside. This step is not required in bulk packed unit.

2 . Hold housing to joist and nail in place through the slotted holes in the mounting ears. Adjust housing edge so that it will be flush with finished plaster line. Then drive nails through round holes in hanger to secure.

110vAC110vAC

DIAGRAM A DIAGRAM B

A.A single toggle switch can control both the fan and light (see diagram A).

B.Fan and light can be controlled individually with separate toggle switches (see diagram B).

Select the manner of the wiring which best suits your needs and complete the wiring as illustrated.

FIGURE 1

CEILING OPENING 71⁄4" X 9"

3" DISCHARGEROOF

VENTILATOR

CEILING INSTALLATION
HORIZONTAL OR
VERTICAL DISCHARGE
90˚	3" WALL
	CAP

3" ROUND	FIGURE 2
ADJUSTABLE ELBOW

3 . Refer to Figure 1. Pull wire through knockout into housing. Make connection and replace receptacle cover. Ground unit to screw inside of switch box.

4 . Refer to Figure 2. Add 3" duct to vent outside. Use roof ventilator or wall cap depending on style of installation being used.

5 . Replace motor-blade assembly making sure plug is toward receptacle and tighten in place. Plug cord into receptacle .

6 . Plug light socket cord into receptacle. Replace grille- reflector-socket assembly and tighten in place with nut.

7 . Install light bulb (not included) in socket. 100 watt maximum. Insert lens. If lens appears to be slightly larger than opening in grille, rotate lens 90° and try inserting lens again.