Cabling and RJ-45 connector wiring | Extron electronic ISM 482

Installation, cont’d

Cabling and RJ-45 connector wiring

It is vital that your Ethernet cables be the correct cables, and that they be properly terminated with the correct pinout.

Choosing a network cable

Ethernet links use Category (CAT) 3, 4, 5, 5e, or 6, unshielded twisted pair (UTP) or shielded twisted pair (STP) cables, terminated with RJ-45 connectors. Ethernet cables are limited to 328' (100 m).

Do not use standard telephone cables. Telephone cables will not support

Ethernet or Fast Ethernet.

Do not stretch or bend cables. Transmission errors can occur.

The cable used depends on your network speed. The ISM supports both 10 Mbps (10Base-T — Ethernet) and 100 Mbps (100Base-T — Fast Ethernet), half-duplex and full-duplex, Ethernet connections.

•10Base-T Ethernet requires, at a minimum, CAT 3 UTP or STP cable.

•100Base-T Fast Ethernet requires, at a minimum, CAT 5 UTP or STP cable.

Wiring the network cable

The cable can be terminated as either a patch cable or a crossover cable (figure 2-8) and must be properly terminated for your application:

•Patch (straight) cable — Connection of the ISM to an Ethernet hub, router, or switcher that also hosts a controlling computer

•Crossover cable — Direct connection between the ISM and a controlling computer

Patch (straight) cable

							Side 1		Side 2
						Pin	Wire color	Pin	Wire color
						1	White-orange	1	White-orange

Side			Pins:		RJ-45	2	Orange	2	Orange
Side			Pins:			3	White-green	3	White-green
	1 2 3 4 5 6 7 8
	1 2 3 4 5 6 7 8				Connector
						4	Blue	4	Blue
						4	Blue	4	Blue

						5	White-blue	5	White-blue
						5	White-blue	5	White-blue
						6	Green	6	Green
						7	White-brown	7	White-brown



						8	Brown	8	Brown
						8	Brown	8	Brown
							Crossover cable
							Crossover cable

			Insert				Side 1		Side 2
			twisted			Pin	Wire color	Pin	Wire color
	pair wires.					1	White-orange	1	White-green
						1	White-orange	1	White-green
						2	Orange	2	Green

						3	White-green	3	White-orange

						4	Blue	4	Blue

						5	White-blue	5	White-blue

						6	Green	6	Orange

						7	White-brown	7	White-brown

						8	Brown	8	Brown

Figure 2-8 — RJ-45 connector pinout tables

2-8 Integration Scaling Matrix Switcher • Installation

Image 23

Extron electronic ISM 482 manual Cabling and RJ-45 connector wiring, Choosing a network cable, Wiring the network cable

Contents

ISM Precautions FCC Class B Notice Integration Scaling Matrix Switcher Quick Start QS-1 Quick Start Integration Scaling Matrix Switcher QS-2 Integration Scaling Matrix Switcher Quick Start Quick Start Integration Scaling Matrix Switcher, cont’d Table of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One About this Manual About the SwitcherIntegration Scaling Matrix Switcher Introduction Introductiontroduction, cont’d Extron ISM Introduction, cont’d Integration Scaling Matrix Switcher Introduction Introduction, cont’d Two Rack mounting Installationstallation, cont’dMounting the Switcher Tabletop placement Mounting instructions Mounting the switcher Input connections Installation, cont’dCabling and Rear Panel Views Captive screw connector wiring for inputs BNC output connections for Rgbhv and Rgbs video Standard output connections Optional output connection Choosing a network cable Cabling and RJ-45 connector wiringWiring the network cable RS-232 connection Configuration Installation, cont’d Three Video/Audio selection button and LEDs Front Panel Controls and IndicatorsIntegration Scaling Matrix Switcher Operation Operationeration, cont’d Front panel input label window Output buttons and LEDsInput buttons, LEDs, and label window Black/Mute button and LEDs Picture adjustment buttonsOperation, cont’d Menu control buttons Adjustment knobsLCD display Front Panel Operations Power Extron Electronics ISM 60-425-01 Version Menu system overview Input Configuration submenu Video & Audio Configuration menu Output Resolution submenu Output Configuration menu Operation, cont’d 10 Advanced Configuration menu flowchart Blanking submenu Blue-Only Mode and Edge Smoothing submenuRGB Delay submenu Test Pattern submenu Reset submenu Enhanced Mode submenuPixel Phase submenu PAL Film Mode submenu Save Preset submenu User Presets menu Exit menu Erase Preset submenu 13 Picture adjustments flowchart Picture adjustments Adjust knobs have no mechanical limits to their rotation Front panel security lockout Executive mode IP information Optimizing the Video Centering controls to position the image Setting up a DVD source General checks TroubleshootingOptimizing the Audio Problem Cause Specific problems Operation, cont’d Four Ethernet Link Integration Scaling Matrix Switcher Programmer’s GuideRS-232 Link Ethernet connection SymbolsDefault address Ties creation Switcher-Initiated MessagesPower-up Programmer’s Guide, cont’d X2 Col Test pattern RGB delayPAL film mode Automated adjustments Using the command/response table Host-to-Switcher InstructionsSwitcher error responses Programmer’s Guide, cont’d Command Ascii Command Response Additional description Command/response table for SIS commands cont’d Horizontal detail filter RGB and component video inputs User presets Verbose mode Resets Command/response table for IP SIS commands Command/response table for IP SIS commands Command/response table for special function SIS commands X2 Reconfig message may not be Command Hex Command Response Command/response table for advanced instruction set commands Five Control Software for Windows Installing the softwareIntegration Scaling Matrix Switcher Switcher Software Software operation via Ethernet Ethernet protocol settings Using the control program Switcher Software, cont’d Windows Control program window Button-Label Generator Using the help program To run the Button-Label Generator program, click Start Using the software Switcher Software, cont’d Six Loading the Startup Control Integration Scaling Matrix Switcher Ethernet OperationEthernetOperation,cont’d Control Creating a tie Changing the RGB delayEthernet Operation, cont’d Control Outputting a test pattern Using Blue-Only modeExecutive mode Freezing the output System Configuration System Configuration ISM Name field Administration fieldsISM IP Settings fields ISM IP Address field File Management File Management I/O Configuration Input configuration Ethernet Operation, cont’d Output rate Output resolution Output polarity Output format Seven Opening and Closing the Switcher Maintenance and Modifications Grounding wrist strap is recommended Installing a Firmware Upgrade Maintenance and Modifications, Cont’d DVI output card connector opening and socket J14 Installing a DVI Output Card Output DVI board installation AAppendix a Cabling Integration Scaling Matrix Switcher Ethernet ConnectionEthernet Connection Pinging to determine the Web IP address Determining Default AddressesPinging to determine the switcher’s IP address Open Connecting as a Telnet ClientEthernet Connection, cont’d Telnet tips Close Escape character and Esc keyLocal echo Set carriage return-line feed Ethernet Connection, cont’d AppendixBB Reference Information Audio Reference Information, cont’d Button Labels Reference Information, cont’d Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C