Configuration, RS-232 connection | Extron electronic ISM 482

RS-232 connection

7Remote port — Connect a host device, such as a computer or touch panel control, to the integration scaling matrix switcher via this 9-pin D connector for serial RS-232 control (figure 2-9).

	Pin	RS-232	Function	5	1
	1	—	Not used

	2	TX	Transmit data
	3	RX	Receive data	9	6
	4	—	Not used
				Female
	5	Gnd	Signal ground	1	5
	6	—	Not used
	7	—	Not used
	8	—	Not used	6	9
	9	—	Not used
				Male

Figure 2-9 — Remote port pin assignments

See chapter 4, “Programmer’s Guide”, for definitions of the SIS commands and chapter 5, “Switcher Software” to install and use the control software.

Configuration

The ISM can be configured using either the front panel controls, the SIS, or the Windows Control program. See chapter 3, “Operation”, chapter 4, “Programmer’s Guide”, and chapter 5, “Switcher Software”.

Integration Scaling Matrix Switcher • Installation

2-9

Image 24

Extron electronic ISM 482 manual Configuration, RS-232 connection

Contents

ISM Precautions FCC Class B Notice Quick Start Integration Scaling Matrix Switcher Integration Scaling Matrix Switcher Quick Start QS-1 Quick Start Integration Scaling Matrix Switcher, cont’d QS-2 Integration Scaling Matrix Switcher Quick Start Table of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One About the Switcher Integration Scaling Matrix Switcher IntroductionIntroductiontroduction, cont’d About this Manual Extron ISM Introduction, cont’d Integration Scaling Matrix Switcher Introduction Introduction, cont’d Two Installationstallation, cont’d Mounting the SwitcherTabletop placement Rack mounting Mounting the switcher Mounting instructions Installation, cont’d Cabling and Rear Panel ViewsInput connections Captive screw connector wiring for inputs Standard output connections BNC output connections for Rgbhv and Rgbs video Optional output connection Cabling and RJ-45 connector wiring Wiring the network cableChoosing a network cable Configuration RS-232 connection Installation, cont’d Three Front Panel Controls and Indicators Integration Scaling Matrix Switcher OperationOperationeration, cont’d Video/Audio selection button and LEDs Output buttons and LEDs Input buttons, LEDs, and label windowFront panel input label window Picture adjustment buttons Operation, cont’dBlack/Mute button and LEDs Adjustment knobs LCD displayMenu control buttons Power Front Panel Operations Menu system overview Extron Electronics ISM 60-425-01 Version Video & Audio Configuration menu Input Configuration submenu Output Configuration menu Output Resolution submenu Operation, cont’d 10 Advanced Configuration menu flowchart Blue-Only Mode and Edge Smoothing submenu RGB Delay submenuTest Pattern submenu Blanking submenu Enhanced Mode submenu Pixel Phase submenuPAL Film Mode submenu Reset submenu User Presets menu Save Preset submenu Erase Preset submenu Exit menu Picture adjustments 13 Picture adjustments flowchart Front panel security lockout Executive mode Adjust knobs have no mechanical limits to their rotation Optimizing the Video IP information Setting up a DVD source Centering controls to position the image Troubleshooting Optimizing the AudioGeneral checks Specific problems Problem Cause Operation, cont’d Four Integration Scaling Matrix Switcher Programmer’s Guide RS-232 LinkEthernet Link Symbols Default addressEthernet connection Switcher-Initiated Messages Power-upProgrammer’s Guide, cont’d Ties creation X2 Col RGB delay PAL film modeAutomated adjustments Test pattern Host-to-Switcher Instructions Switcher error responsesUsing the command/response table Programmer’s Guide, cont’d Command/response table for SIS commands cont’d Command Ascii Command Response Additional description Horizontal detail filter RGB and component video inputs User presets Verbose mode Command/response table for IP SIS commands Resets Command/response table for special function SIS commands Command/response table for IP SIS commands X2 Reconfig message may not be Command/response table for advanced instruction set commands Command Hex Command Response Five Installing the software Integration Scaling Matrix Switcher Switcher SoftwareControl Software for Windows Ethernet protocol settings Software operation via Ethernet Switcher Software, cont’d Using the control program Windows Control program window Using the help program Button-Label Generator Using the software To run the Button-Label Generator program, click Start Switcher Software, cont’d Six Integration Scaling Matrix Switcher Ethernet Operation EthernetOperation,cont’dLoading the Startup Control Control Changing the RGB delay Ethernet Operation, cont’dControl Creating a tie Using Blue-Only mode Executive modeFreezing the output Outputting a test pattern System Configuration System Configuration Administration fields ISM IP Settings fieldsISM IP Address field ISM Name field File Management File Management Input configuration I/O Configuration Ethernet Operation, cont’d Output resolution Output rate Output format Output polarity Seven Maintenance and Modifications Opening and Closing the Switcher Grounding wrist strap is recommended Maintenance and Modifications, Cont’d Installing a Firmware Upgrade Installing a DVI Output Card DVI output card connector opening and socket J14 Output DVI board installation AAppendix a Integration Scaling Matrix Switcher Ethernet Connection Ethernet ConnectionCabling Determining Default Addresses Pinging to determine the switcher’s IP addressPinging to determine the Web IP address Connecting as a Telnet Client Ethernet Connection, cont’dTelnet tips Open Escape character and Esc key Local echoSet carriage return-line feed Close Ethernet Connection, cont’d AppendixBB Reference Information Audio Reference Information, cont’d Button Labels Reference Information, cont’d Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C