Programmer’s Guide, cont’d, Power-up | Extron electronic ISM 482

Programmer’s Guide, cont’d

Switcher-Initiated Messages

When a local event such as power-up or a front panel operation occurs, the switcher responds by sending a message to the host. The switcher-initiated messages are listed in the following pages. The messages are underlined.

The switcher does not expect a response from the host; but, for example, the host program might request a new status.

Power-up

(c) Copyright 2002, Extron Electronics, ISM 482, Vx.xx

The switcher initiates the copyright message when it is first powered on. Vxxxx is the firmware version number.

Ties creation

Out X2 •In X1 •All

A front panel video and audio switching operation has occurred. X2 is the output number and X1 is the input number.

Out X2 •In X1 •RGB

A front panel video-only switching operation has occurred. X2 is the output number and X1 is the input number.

Out X2 •In X1 •Aud

A front panel audio-only switching operation has occurred. X2 is the output number and X1 is the input number.

Input and output video type

X1 Typ X4

A front panel input video type selection has occurred. X4 is the input video type.

X2 Rte X5X6

X1

is the input number and

A front panel output video format selection has occurred. X2 is the output number, X5 is the output resolution, and X6 is the output refresh rate.

X2 Syn X7

A front panel output video type selection has occurred. X2 is the output number and X7 is the output video format (RGBHV or RGBS).

X2 Pol X8

A front panel output video polarity selection has occurred. X2 is the output number and X8 is the output sync polarity.

4-4 Integration Scaling Matrix Switcher • Programmer’s Guide

Image 51

Extron electronic ISM 482 manual Programmer’s Guide, cont’d, Switcher-Initiated Messages, Power-up, Ties creation

Contents

ISM Precautions FCC Class B Notice Integration Scaling Matrix Switcher Quick Start QS-1 Quick Start Integration Scaling Matrix Switcher QS-2 Integration Scaling Matrix Switcher Quick Start Quick Start Integration Scaling Matrix Switcher, cont’d Table of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One About this Manual About the SwitcherIntegration Scaling Matrix Switcher Introduction Introductiontroduction, cont’d Extron ISM Introduction, cont’d Integration Scaling Matrix Switcher Introduction Introduction, cont’d Two Rack mounting Installationstallation, cont’dMounting the Switcher Tabletop placement Mounting instructions Mounting the switcher Installation, cont’d Cabling and Rear Panel ViewsInput connections Captive screw connector wiring for inputs BNC output connections for Rgbhv and Rgbs video Standard output connections Optional output connection Cabling and RJ-45 connector wiring Wiring the network cableChoosing a network cable RS-232 connection Configuration Installation, cont’d Three Video/Audio selection button and LEDs Front Panel Controls and IndicatorsIntegration Scaling Matrix Switcher Operation Operationeration, cont’d Output buttons and LEDs Input buttons, LEDs, and label windowFront panel input label window Picture adjustment buttons Operation, cont’dBlack/Mute button and LEDs Adjustment knobs LCD displayMenu control buttons Front Panel Operations Power Extron Electronics ISM 60-425-01 Version Menu system overview Input Configuration submenu Video & Audio Configuration menu Output Resolution submenu Output Configuration menu Operation, cont’d 10 Advanced Configuration menu flowchart Blanking submenu Blue-Only Mode and Edge Smoothing submenuRGB Delay submenu Test Pattern submenu Reset submenu Enhanced Mode submenuPixel Phase submenu PAL Film Mode submenu Save Preset submenu User Presets menu Exit menu Erase Preset submenu 13 Picture adjustments flowchart Picture adjustments Adjust knobs have no mechanical limits to their rotation Front panel security lockout Executive mode IP information Optimizing the Video Centering controls to position the image Setting up a DVD source Troubleshooting Optimizing the AudioGeneral checks Problem Cause Specific problems Operation, cont’d Four Integration Scaling Matrix Switcher Programmer’s Guide RS-232 LinkEthernet Link Symbols Default addressEthernet connection Ties creation Switcher-Initiated MessagesPower-up Programmer’s Guide, cont’d X2 Col Test pattern RGB delayPAL film mode Automated adjustments Host-to-Switcher Instructions Switcher error responsesUsing the command/response table Programmer’s Guide, cont’d Command Ascii Command Response Additional description Command/response table for SIS commands cont’d Horizontal detail filter RGB and component video inputs User presets Verbose mode Resets Command/response table for IP SIS commands Command/response table for IP SIS commands Command/response table for special function SIS commands X2 Reconfig message may not be Command Hex Command Response Command/response table for advanced instruction set commands Five Installing the software Integration Scaling Matrix Switcher Switcher SoftwareControl Software for Windows Software operation via Ethernet Ethernet protocol settings Using the control program Switcher Software, cont’d Windows Control program window Button-Label Generator Using the help program To run the Button-Label Generator program, click Start Using the software Switcher Software, cont’d Six Integration Scaling Matrix Switcher Ethernet Operation EthernetOperation,cont’dLoading the Startup Control Control Creating a tie Changing the RGB delayEthernet Operation, cont’d Control Outputting a test pattern Using Blue-Only modeExecutive mode Freezing the output System Configuration System Configuration ISM Name field Administration fieldsISM IP Settings fields ISM IP Address field File Management File Management I/O Configuration Input configuration Ethernet Operation, cont’d Output rate Output resolution Output polarity Output format Seven Opening and Closing the Switcher Maintenance and Modifications Grounding wrist strap is recommended Installing a Firmware Upgrade Maintenance and Modifications, Cont’d DVI output card connector opening and socket J14 Installing a DVI Output Card Output DVI board installation AAppendix a Integration Scaling Matrix Switcher Ethernet Connection Ethernet ConnectionCabling Determining Default Addresses Pinging to determine the switcher’s IP addressPinging to determine the Web IP address Open Connecting as a Telnet ClientEthernet Connection, cont’d Telnet tips Close Escape character and Esc keyLocal echo Set carriage return-line feed Ethernet Connection, cont’d AppendixBB Reference Information Audio Reference Information, cont’d Button Labels Reference Information, cont’d Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C