Front Panel Operations, Power | Extron electronic ISM 482 instruction

Operation, cont’d

Front Panel Operations

The following paragraphs detail the power-up process and then describe the menu system, the picture adjustments, and selection of executive mode.

Power

Power is automatically applied when the power cord is connected to an AC source. When AC power is applied, the switcher performs a self-test that blinks all of the front panel LEDs and then lights only the LEDs for the previously selected output and the tied input. The self-test also displays the model name, part number, and the firmware version in the LCD display. After approximately 2 seconds, the LCD reverts to its default display cycle, alternating between two displays: one showing the inputs selected for outputs 1 and output 2, and the other showing the selected output rates (figure 3-6). An error-free power up self-test sequence leaves all of the LEDs off, with the exception of the selected output’s and input’s LEDs, off and the LCD cycling through the default displays.

		Extron Electronics
Power		ISM 482	2
on		Integration	2
		Scaling Matrix	sec.
		Scaling Matrix

Extron Electronics

ISM 482

60-425-01

Version x.xx

Default Display Cycle

	Out #1 In # 1 RGB			Output Rate
	0.00 kHz	0.00Hz		#1 1280 x 1024 @ 60
2	Out #2 In # 3 S-Video		2
sec.	0.00 kHz	0.00Hz	sec.	#2 1280 x 1024 @ 60
	0.00 kHz	0.00Hz		#2 1280 x 1024 @ 60
				2
				sec.

Figure 3-6 — LCD power up and default display cycle

The selected inputs for output 1 and output 2, the picture adjustments, and other current settings are saved in nonvolatile memory. When power is applied, the latest configuration is retrieved.

On figure 3-6 and all other flowcharts in this chapter, solid lines indicate screen changes initiated by the operator. Dashed lines indicate screen changes that are the result of a timeout function.

3-6 Integration Scaling Matrix Switcher • Operation

Image 31

Extron electronic ISM 482 manual Front Panel Operations, Power

Contents

ISM Precautions FCC Class B Notice Integration Scaling Matrix Switcher Quick Start QS-1 Quick Start Integration Scaling Matrix Switcher QS-2 Integration Scaling Matrix Switcher Quick Start Quick Start Integration Scaling Matrix Switcher, cont’d Table of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One About this Manual About the SwitcherIntegration Scaling Matrix Switcher Introduction Introductiontroduction, cont’d Extron ISM Introduction, cont’d Integration Scaling Matrix Switcher Introduction Introduction, cont’d Two Rack mounting Installationstallation, cont’dMounting the Switcher Tabletop placement Mounting instructions Mounting the switcher Cabling and Rear Panel Views Installation, cont’dInput connections Captive screw connector wiring for inputs BNC output connections for Rgbhv and Rgbs video Standard output connections Optional output connection Wiring the network cable Cabling and RJ-45 connector wiringChoosing a network cable RS-232 connection Configuration Installation, cont’d Three Video/Audio selection button and LEDs Front Panel Controls and IndicatorsIntegration Scaling Matrix Switcher Operation Operationeration, cont’d Input buttons, LEDs, and label window Output buttons and LEDsFront panel input label window Operation, cont’d Picture adjustment buttonsBlack/Mute button and LEDs LCD display Adjustment knobsMenu control buttons Front Panel Operations Power Extron Electronics ISM 60-425-01 Version Menu system overview Input Configuration submenu Video & Audio Configuration menu Output Resolution submenu Output Configuration menu Operation, cont’d 10 Advanced Configuration menu flowchart Blanking submenu Blue-Only Mode and Edge Smoothing submenuRGB Delay submenu Test Pattern submenu Reset submenu Enhanced Mode submenuPixel Phase submenu PAL Film Mode submenu Save Preset submenu User Presets menu Exit menu Erase Preset submenu 13 Picture adjustments flowchart Picture adjustments Adjust knobs have no mechanical limits to their rotation Front panel security lockout Executive mode IP information Optimizing the Video Centering controls to position the image Setting up a DVD source Optimizing the Audio TroubleshootingGeneral checks Problem Cause Specific problems Operation, cont’d Four RS-232 Link Integration Scaling Matrix Switcher Programmer’s GuideEthernet Link Default address SymbolsEthernet connection Ties creation Switcher-Initiated MessagesPower-up Programmer’s Guide, cont’d X2 Col Test pattern RGB delayPAL film mode Automated adjustments Switcher error responses Host-to-Switcher InstructionsUsing the command/response table Programmer’s Guide, cont’d Command Ascii Command Response Additional description Command/response table for SIS commands cont’d Horizontal detail filter RGB and component video inputs User presets Verbose mode Resets Command/response table for IP SIS commands Command/response table for IP SIS commands Command/response table for special function SIS commands X2 Reconfig message may not be Command Hex Command Response Command/response table for advanced instruction set commands Five Integration Scaling Matrix Switcher Switcher Software Installing the softwareControl Software for Windows Software operation via Ethernet Ethernet protocol settings Using the control program Switcher Software, cont’d Windows Control program window Button-Label Generator Using the help program To run the Button-Label Generator program, click Start Using the software Switcher Software, cont’d Six EthernetOperation,cont’d Integration Scaling Matrix Switcher Ethernet OperationLoading the Startup Control Control Creating a tie Changing the RGB delayEthernet Operation, cont’d Control Outputting a test pattern Using Blue-Only modeExecutive mode Freezing the output System Configuration System Configuration ISM Name field Administration fieldsISM IP Settings fields ISM IP Address field File Management File Management I/O Configuration Input configuration Ethernet Operation, cont’d Output rate Output resolution Output polarity Output format Seven Opening and Closing the Switcher Maintenance and Modifications Grounding wrist strap is recommended Installing a Firmware Upgrade Maintenance and Modifications, Cont’d DVI output card connector opening and socket J14 Installing a DVI Output Card Output DVI board installation AAppendix a Ethernet Connection Integration Scaling Matrix Switcher Ethernet ConnectionCabling Pinging to determine the switcher’s IP address Determining Default AddressesPinging to determine the Web IP address Open Connecting as a Telnet ClientEthernet Connection, cont’d Telnet tips Close Escape character and Esc keyLocal echo Set carriage return-line feed Ethernet Connection, cont’d AppendixBB Reference Information Audio Reference Information, cont’d Button Labels Reference Information, cont’d Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C