Standard output connections | Extron electronic ISM 482 instruction

Installation, cont’d

Standard output connections

The two Output 1 outputs, consisting of five BNC connectors and a 15-pin

HD connector, output the identical video signal and the same sync format.

The two Output 2 outputs are also identical to each other.

4Video output BNC connectors — Connect RGB video displays to these two sets of female BNC connectors. Figure 2-6 shows how to connect the various video formats.

RR

GG

BB

H/HV H/HV

VV

RGBHV RGBS

Video Video

Figure 2-6 — BNC output connections for RGBHV and RGBS video

Video output 15-pin HD connectors — Connect RGB video displays to these two female 15-pin HD connectors.

5Audio output connectors — Connect audio devices, such as an audio amplifier or powered speakers, to these two 3.5 mm, 5-pole captive screw connectors. The connectors output the selected unamplified, line level audio. See figure 2-7 to properly wire an output connector.

	Tip	L	Tip
	NO GROUND HERE.		Ring

	Sleeve(s)		Tip
	Tip	R
	NO GROUND HERE.		Ring

				0.2” (5 mm) max.	Unbalanced	Balanced

Do not tin the wires!					Stereo Output	Stereo Output

L R

Figure 2-7 — Captive screw connector wiring for audio output

CAUTION

CAUTION

Connect the sleeve to ground (Gnd). Connecting the sleeve to a negative (-) terminal will damage the audio output circuits.

The length of exposed wires is critical. The ideal length is 0.2" (5 mm).

•If the stripped section of wire is longer than 0.2", the exposed wires may touch, causing a short circuit between them.

•If the stripped section of wire is shorter than 0.2", wires can be easily pulled out even if tightly fastened by the captive screws.

By default, the audio output follows the video switch. Audio breakaway, commanded via the front panel, the Ethernet link, or the RS-232 link, allows you to select from any one of the audio input sources. See chapter 3, “Operation”, chapter 4, “Programmer’s Guide”, chapter 5, “Switcher Software”, and chapter 6, “Ethernet Operation” for details.

2-6 Integration Scaling Matrix Switcher • Installation

Image 21

Extron electronic ISM 482 manual Standard output connections, BNC output connections for Rgbhv and Rgbs video

Contents

ISM Precautions FCC Class B Notice Integration Scaling Matrix Switcher Quick Start QS-1 Quick Start Integration Scaling Matrix Switcher QS-2 Integration Scaling Matrix Switcher Quick Start Quick Start Integration Scaling Matrix Switcher, cont’d Table of Contents Table of Contents, cont’d Integration Scaling Matrix Switcher Table of Contents Iii Iv Integration Scaling Matrix Switcher Table of Contents One Integration Scaling Matrix Switcher Introduction About the SwitcherIntroductiontroduction, cont’d About this Manual Extron ISM Introduction, cont’d Integration Scaling Matrix Switcher Introduction Introduction, cont’d Two Mounting the Switcher Installationstallation, cont’dTabletop placement Rack mounting Mounting instructions Mounting the switcher Installation, cont’d Cabling and Rear Panel ViewsInput connections Captive screw connector wiring for inputs BNC output connections for Rgbhv and Rgbs video Standard output connections Optional output connection Cabling and RJ-45 connector wiring Wiring the network cableChoosing a network cable RS-232 connection Configuration Installation, cont’d Three Integration Scaling Matrix Switcher Operation Front Panel Controls and IndicatorsOperationeration, cont’d Video/Audio selection button and LEDs Output buttons and LEDs Input buttons, LEDs, and label windowFront panel input label window Picture adjustment buttons Operation, cont’dBlack/Mute button and LEDs Adjustment knobs LCD displayMenu control buttons Front Panel Operations Power Extron Electronics ISM 60-425-01 Version Menu system overview Input Configuration submenu Video & Audio Configuration menu Output Resolution submenu Output Configuration menu Operation, cont’d 10 Advanced Configuration menu flowchart RGB Delay submenu Blue-Only Mode and Edge Smoothing submenuTest Pattern submenu Blanking submenu Pixel Phase submenu Enhanced Mode submenuPAL Film Mode submenu Reset submenu Save Preset submenu User Presets menu Exit menu Erase Preset submenu 13 Picture adjustments flowchart Picture adjustments Adjust knobs have no mechanical limits to their rotation Front panel security lockout Executive mode IP information Optimizing the Video Centering controls to position the image Setting up a DVD source Troubleshooting Optimizing the AudioGeneral checks Problem Cause Specific problems Operation, cont’d Four Integration Scaling Matrix Switcher Programmer’s Guide RS-232 LinkEthernet Link Symbols Default addressEthernet connection Power-up Switcher-Initiated MessagesProgrammer’s Guide, cont’d Ties creation X2 Col PAL film mode RGB delayAutomated adjustments Test pattern Host-to-Switcher Instructions Switcher error responsesUsing the command/response table Programmer’s Guide, cont’d Command Ascii Command Response Additional description Command/response table for SIS commands cont’d Horizontal detail filter RGB and component video inputs User presets Verbose mode Resets Command/response table for IP SIS commands Command/response table for IP SIS commands Command/response table for special function SIS commands X2 Reconfig message may not be Command Hex Command Response Command/response table for advanced instruction set commands Five Installing the software Integration Scaling Matrix Switcher Switcher SoftwareControl Software for Windows Software operation via Ethernet Ethernet protocol settings Using the control program Switcher Software, cont’d Windows Control program window Button-Label Generator Using the help program To run the Button-Label Generator program, click Start Using the software Switcher Software, cont’d Six Integration Scaling Matrix Switcher Ethernet Operation EthernetOperation,cont’dLoading the Startup Control Control Ethernet Operation, cont’d Changing the RGB delayControl Creating a tie Executive mode Using Blue-Only modeFreezing the output Outputting a test pattern System Configuration System Configuration ISM IP Settings fields Administration fieldsISM IP Address field ISM Name field File Management File Management I/O Configuration Input configuration Ethernet Operation, cont’d Output rate Output resolution Output polarity Output format Seven Opening and Closing the Switcher Maintenance and Modifications Grounding wrist strap is recommended Installing a Firmware Upgrade Maintenance and Modifications, Cont’d DVI output card connector opening and socket J14 Installing a DVI Output Card Output DVI board installation AAppendix a Integration Scaling Matrix Switcher Ethernet Connection Ethernet ConnectionCabling Determining Default Addresses Pinging to determine the switcher’s IP addressPinging to determine the Web IP address Ethernet Connection, cont’d Connecting as a Telnet ClientTelnet tips Open Local echo Escape character and Esc keySet carriage return-line feed Close Ethernet Connection, cont’d AppendixBB Reference Information Audio Reference Information, cont’d Button Labels Reference Information, cont’d Integration Scaling Matrix Switcher Reference Information Reference Information, cont’d Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C