Clearing Paper Jams, Rear Feed Jams | Oki ML5520, ML5521 manual

3.Adjust the paper feed guides (1) for the width of the paper, then place a sheet of paper in the separator. The paper will feed into the printer.

1

NOTES

>If the paper does not feed in, remove it. Check the paper lever position. Make sure the ALARM light is ON: if it is flashing, hold the SHIFT key and press the CHARACTER PITCH/RESET key. Reload the sheet of paper.

>The factory default setting for the Top of Form (where the printing should begin) is 1" down from the top of the page. To change the setting, see “Top of Form (TOF)” in the previous chapter.

CLEARING PAPER JAMS

REAR FEED JAMS

1.Turn the printer OFF.

2.Use the platen knob to back the paper all the way out of the printer.

CAUTION!

Make sure the printer is turned OFF before you open the access cover.

MAINTENANCE > 55

Image 55

Oki ML5520, ML5521 manual Clearing Paper Jams, Rear Feed Jams

Contents

ML5520/21 Preface Contents Index Oki contact details Page Paper Park Features / TipsIntroduction Forms Tear-Off Turning the Platen Knob Top of Form TOF Controlling Access to the Printer Printer Drivers Installing the DriverPrinter Drivers Emulations Epson FX Using a Compatible DriverInterfaces General IBM Proprinter Printer’s USB port Connecting the USB Cable Printer Drivers Components Rear Feed Continuous Forms Using Your PrinterComponents TOP Feed Single Sheets TOP of Form TOF To print the Menu Forms TEAR-OFFTo use the Tear key Forms Tear-Off set to OFF default Setting TOP of Form TOF Forms Tear-Off set to on SEL light goes off and the red alarm light comes on Temporarily Changing the TOP of Form Forms TEAR-OFF Feature Potential Issues with Software Packages Manual Forms TEAR-OFF Changing the Forms TEAR-OFF Setting Never park labels Paper ParkChanging Paper Paths Continuous Forms to Single Sheets Single Sheets to Continuous Forms Press FF/LOAD Printhead GAP Setting Media Super Speed Draft SSD Utility UTL-the defaultPrint Quality High Speed Draft HSD Epson and IBM Emulations Character PitchMicroline Emulation Emulations Printer ResetChanging Emulations Menu Mode Keys Menu Mode Printing ALL Menu Settings Entering and Exiting Menu ModeResetting the Menu to the Factory Defaults Printing the Menu Settings Group Settings Menu Settings 13.6 17.1 cpi, 20 cpi Invalid, Valid Explanation of Menu Items Busy Line, Default = SSD Baud Rate, Default = 9600 bpsBi-direction, Default = Enable Bottom Margin, Default = Valid CSF Bin Select, Default = Bin Character Set, Default = IBM SetCharacter Set, Default = Standard Code Page, Default = USA ESC SI Pitch, Default = 17 cpi DSR Signal, Default = ValidDTR Signal, Default = Ready On Power Up Emulation Mode, Default = IBM PPR Length, Default = 11-2/3 or 1/2 Language Set, Default = AsciiLine Spacing, Default = 6 lpi Operator Panel Function, Default = Full Operation Print Mode, Default = Utility Paper Out Override, Default = NoPower Save Time, Default = 5 min Power Saving, Default = Enable Protocol, Default = Ready/Busy Print Registration, Default =Print Suppress Effective, Default = Yes Proportional Spacing, Default = No Skip Over Perforation, Default = No SI Select Pitch 10 cpi, Default = 17.1 cpiSI Select Pitch 12 cpi, Default = 20 cpi Size, Default = Single Replacing the Ribbon Cartridge Maintenance If ribbon should contact the eyes Printhead may be HOTIf ribbon should contact the skin Rear Feed Loading PaperLoading Rear Feed Paper from the Back of the Printer Maintenance 5520 5521 If the paper is too loose, or too tight, it can cause jams Maintenance Loading Rear Feed Paper from the Front of the Printer 10 9.516 If the paper is too loose or too tight it can cause jams Reinstall the sheet feeder Maintenance TOP Feed Single Sheets Rear Feed Jams Clearing Paper Jams Maintenance Defective Paper Rear FEED, Repeating Paper JamsMisaligned Paper Maintenance Maintenance Single Sheet Paper Jams Cleaning the Housing Maintenance General Information TroubleshootingProblem Solution Solutions Ink smears on the paper when I print narrow columns There are dots missing in my printouts Continuous-form paper sticks to the sheet guide Purchasing Parts & Accessories Parts and Accessories Option Part number ML5520 ML5521 Printer Control Codes IBM Proprinter III Commands ESC % G Epson FX Commands DC3 OKI Microline Standard Commands ESC Y OFF Escz Specification Specifications UPC A, UPC E Top only Paper Specifications ML5520 Location Setting UP Your PrinterUnpacking Setting UP Your Printer Setting UP Your Printer Ribbon Cartridge Handling Installing the Ribbon CartridgePage Power Connection Computer Connections USB, Specification 1.1 CompliantParallel LPT, Ieee Loading Paper Testing the Printer Font Sample Test Setting UP Your Printer Hexadecimal Dump Mode Buffer Index Length Time Out Oki Hong Kong Limited Oki Systems UK LimitedOki Systems Ireland Limited Oki Data Corporation ML5520/21