Marantz NR1501 Specifications, Using Headphones, Copyright, Names, Connections, Basic, Setup

NAMES

ENGLISH

OTHERS

FUNCTIONS	AND
CONNECTIONS	BASIC

SPECIFICATIONS

FM TUNER SECTION

Frequency Range	87.5 MHz to 108.0 MHz
Usable Sensitivity	IHF 1.8 μV/16.4 dBf

Signal to Noise Ratio (Mono/Stereo)

............................................ 75 dB / 70 dB

Frequency Response (Analog Input / Pure Direct)

........................... 8 Hz to 100 kHz (± 3 dB)

(Digital Input / 96 kHz PCM)

............................. 8 Hz to 45 kHz (± 3 dB)

USING HEADPHONES

Take care not to turn up the volume too high while you are using headphones. Listening to sound at high-volume levels for prolonged periods can negatively affect your hearing.

COPYRIGHT

REPAIRS

Only the most competent and qualified service technicians should be allowed to service the factory-trained warranty station personnel have the knowledge and special facilities needed for repair and calibration of this precision equipment. After the warranty period has expired, repairs will be performed for a charge if the equipment can be returned to normal operation.

BASIC OPERATION

Distortion (Mono/Stereo)	0.3 % / 0.5 %
Stereo Separation	1 kHz 35 dB
Alternate Channel Selectivity ...	± 300 kHz 60 dB
Image Rejection	98 MHz 60 dB

Tuner Output Level (1 kHz, ± 75 kHz Dev)

......................................................500 mV

VIDEO

Television Format	NTSC
Input Level/Impedance	1 Vp-p / 75 Ω
Output Level/Impedance	1 Vp-p / 75 Ω

Video Frequency Response

.............................. 5 Hz to 8 MHz (- 1 dB)

Recording and playback of any material may require consent. For further information refer to the following:

—Copyright Act 1956

—Dramatic and Musical Performers Act 1958

—Performers Protection Acts 1963 and 1972

—Any subsequent statutory enactments and orders

In the event of difficulty, refer to your dealer or write directly to the nearest location to you that is listed on the Marantz Authorized Service Station list. If writing, please include the model and serial number of the equipment together with a full description of what you think is abnormal about the equipment’s behavior.

ADVANCED CONNECTIONS

SETUP

AM TUNER SECTION

Frequency Range	530 kHz to 1710 kHz
Signal to Noise Ratio	40 dB
Usable Sensitivity (Loop Antenna)......400 μV/m
Distortion	400 Hz, 30 % Mod. 0.7 %
Selectivity	± 18 kHz 70 dB

Video Frequency (Component)

............................	5 Hz to 80 MHz (- 1 dB)
S/N	60 dB
HDMI
Version	1.3a [INPUT]
..................................	1.3a [OUTPUT]

GENERAL

CLEANING OF EQUIPMENT

EXTERNAL SURFACES

The exterior finish of your unit will last indefinitely with proper care and cleaning, Never use scouring pads, steel wool, scourging powders or harsh chemical agents (e.g., lye solution), alcohol, thinner, benzine, insecticide or other volatile substances as these wil mar the finish of the equipment. Likewise,

ADVANCED OPERATION

TROUBLESHOOTING

OTHERS

AUDIO SECTION

Power Output (20 Hz – 20 kHz/THD=0.08%)
Front L&R (8 ohm load, Per channel) ..		50	W
Center (8 ohm load, Per channel)		50	W
Surround L&R (8 ohm load, Per channel)
..........................................................		50 W
Surround Back L&R
(8 ohm load, Per channel)		50	W
Power Output
Front L&R (6 ohm load, Per channel) ....		60	W
Center (6 ohm load, Per channel)		60	W
Surround L&R (6 ohm load, Per channel)
..........................................................		60 W
Surround Back L&R
(6 ohm load, Per channel)		60	W
Input Sensitivity/Impedance	200 mV / 47 kΩ

Signal to Noise Ratio(Analog Input / Pure Direct)

....................................................... 100 dB

Power Requirement	AC 120 V 60 Hz
Power Consumption	250 W
Standby Power Consumption	0.5 W

Specifications subject to change without prior notice.

never use cloths containing chemical substances. If the equipment get dirty, wipe the external surfaces with a soft, lint-free cloth.

If the equipment becomes heavily soiled:

•dilute some washing up liquid in water, in a ratio of one part detergent to six parts water.

•dip a soft, lint free in the solution and wring the it is damp.

•wipe the equipment with the damp cloth.

•dry the equipment by wiping it with a dry cloth.

42