ENGLISH
CONNECTING SPEAKER WIRE
1. Strip away approx. 10 mm (3/8 inch) of wire insulation.
2. Twist the bared wire ends tight, to prevent short circuits.
CONNECTING AUDIO COMPONENTS
The VCR OUT terminals are for recording purposes. The sound of the analog input source component currently selected is output from these terminals.
The digital sound, which has been input to the DIGITAL IN or HDMI terminal, is not output from the VCR OUT terminals.
BASIC CONNECTIONS
CONNECTING DIGITAL AUDIO
COMPONENTS
• There are 3 digital inputs, 2 coaxial jacks and |
1 optical jack, on the rear panel. You can use |
these jacks to input PCM, Dolby Digital and DTS |
NAMES AND FUNCTIONS |
1.2.
10mm
(3/8 inch)
FRONT R/L
CENTER
SURROUND R/L
3. Loosen the knob by turning it counterclockwise.
| CD Player |
OUT | DIGITAL |
L | OUTPUT |
| |
R |
|
L R |
|
R L |
|
Analog Audio
L R
Digital Audio (coaxial)
| bitstream signals from a CD, DVD, or other digital |
| source components. |
• | Refer to the instructions for each component. To |
| setup the digital audio format of DVD player, or |
| other digital source’s connected to digital input |
| jacks. |
• Use fiber optical cables (optical) for DIGITAL | |
| |
| cables (for digital audio or video) for DIGITAL |
| |
• | You can designate the input for each digital input/ |
| output jacks according to your component. (See |
BASIC | CONNECTIONS |
BASIC | OPERATION |
4. Insert the bare part of the wire into the hole in side of each terminal.
5. Tighten the knob by turning it clockwise to secure the wire.
3. 4. 5.
MONITOR OUT OUT | DVD | MONITOR OUT |
GAME | DVD | DSS | OUT |
FM |
|
|
|
|
|
|
|
|
| 3 |
|
|
|
|
IN | IN | IN | Y | PB/CB | PR/CR | Y | PB/CB | PR/CR |
|
|
|
|
| |
(75Ω) | DVD | DSS | VCR |
| DSS |
|
| VCR |
|
|
|
|
|
|
|
| VIDEO |
|
|
| COMPONENT VIDEO |
|
|
|
|
|
| ||
GND | L |
|
|
|
|
| PRE OUT |
|
| 2 |
|
|
|
|
AM |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| R |
|
|
|
|
|
|
|
| 1 |
|
|
|
|
| IN | IN | IN | OUT | IN | IN | SUB |
|
| R - FRONT - L | CENTER | R - SURR. - L | R | L |
| IN | OUT | IN |
|
| SURROUND BACK | ||||||||
| DVD | DSS |
| VCR | CD | AUX 2 | WOOFER | DIGITAL |
|
| ||||
ANTENNA |
|
| ANALOG AUDIO |
|
|
| REMOTE CONTROL | SPEAKER SYSTEMS : |
|
| ||||
|
|
|
|
| AUDIO |
|
| |||||||
MODEL NO. NR1501
AC IN
page 20) |
Note
•The digital signal jacks on this unit conform to the EIA standard. If you use a cable that does not conform to this standard, this unit may not function properly.
ADVANCED CONNECTIONS |
SETUP |
SURROUND BACK R/L
3. Push the lever and hold it down.
4. Insert the twisted ends of the wires into the hole in the terminal.
5. Release the lever.
3. 4. 5.
Notes
•Do not connect this unit and other components to mains power until all connections between components have been completed.
•Insert all plugs and connectors securely. Incomplete connections may make noise.
•Be sure to connect the left and right channels properly.
Red connectors are for the R (right) channel, and white connectors are for the L (left) channel.
•Be sure to connect input and output properly.
•Refer to the instructions for each component that is connected to this unit.
•Do not bundle the connected cables with the power cord or speaker cables. Doing so may produce noise.
ADVANCED OPERATION |
TROUBLESHOOTING |
OTHERS |
9
