ENGLISH
REMOTE CONTROLLER
OPERATION
NORMAL MODE
WHEN OPERATING MARANTZ AV EQUIPMENT PRODUCTS
This remote controller is preset with a total of 10 types of remote codes, including Marantz BD (Blu- ray), GAME, DVD, VCR (VCR deck), DSS (satellite broadcasting tuner), TUNER, CD, AUX1, AUX2, and AMP (amplifier).
1. Press the SOURCE button. For this example, press DVD.
Pressing the SOURCE button once changes the remote control to the settings for the source that was pressed.
To change the amplifier on other source, press the SOURCE button twice (double- click). The code is sent, and then the amplifier source changes to DVD.
PRESET MODE
Importants
•Some codes may be not match your equipment.
•The preset codes do not cover full functions.
•When the batteries are getting weak, the preset procedure is not successful.
PROGRAMMING WITH THE 4-DIGIT CODE
1.
2.
1.
1.
1. Press and hold down the SOURCE button for the appliance which should be controlled and press SET button until the SEND indicator blinks twice. Then SET indicator flashes.
In case of TV, press and hold down the TV Power On/off button and SET button.
2. Press the
1. Switch on the appliance which should be controlled.
2. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice. Then SET indicator flashes.
In case of TV, press and hold down the TV Power On/off button and SET button.
3. Aim the remote control at the appliance and slowly alternate between pressing INPUT 3 button and the SOURCE ON/OFF button for the appliance.
In case of TV, press INPUT 3 button and the TV Power On/off button alternately.
4. Stop when the appliance turns off.
5. Press ENTER button once to lock in the code.
CHECKING THE CODE
2.
ADVANCED OPERATION
Note
If a code digit is “0”, the SEND indicator will not blink.
4. Repeat step 3 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit.
RESETTING THE CODE
1.
1.
2.
1.
NAMES AND | FUNCTIONS |
BASIC | CONNECTIONS |
BASIC | OPERATION |
ADVANCED | CONNECTIONS |
WHEN OPERATING NON-MARANTZ AV EQUIPMENT PRODUCTS
appliance (code table at the end of this book) When the procedure is successful, the SEND indicator will blink twice.
1.
3.
4.
1. Press and hold down the SOURCE button
SETUP |
This remote controller is preset with remote control codes from AV equipment by other manufacturers. The preset codes are TV, CD, DVD, BD and DSS. Settings can be made in one of two ways.
When the preset codes are set, the following codes are contained in the source button of the remote controller.
See the attached manufacturer number list for the preset manufacturers, devices, preset numbers, and other settings.
Remote | Corresponding |
|
controller | Device name | |
source name | preset code |
|
|
| |
TV | TV | Television |
BD |
|
|
DVD | DVD | DVD player |
CD | CD | CD player |
|
| Satellite |
DSS | SATELLITE | broadcasting |
|
| tuner equipment |
Note
If the indicator did not blink twice, then repeat steps 1 through 2 and try entering the same code again.
SCANNING THE CODE TABLE
2. |
3. |
2. |
3. |
5. |
2. |
1.
1.
1. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice then SET indicator flashes.
In case of TV, press and hold down the TV Power On/off button and SET button.
2. Press the INFO button.
The SEND indicator will blink twice.
3. To view the code for first digit, press 1 once.
Wait 3 seconds, count the SEND indicator blinks (e.g. 3 blinks = 3) and write down the number.
for appliance which should be controlled and press SET button until the SEND indicator blinking twice.
Then SET indicator flashes.
In case of TV, press and hold down the TV Power On/off button and SET button.
2. Press the below codes to reset. TV : 1000
DVD : 2000
CD : 3000
DSS : 4000
BD : 5000
The indicator will blink twice.
Note
After this procedure, the selected SOURCE button is set initial code.
ADVANCED OPERATION |
TROUBLESHOOTING |
OTHERS |
31
