Manuals / Omega Engineering / Marine Equipment / Marine Battery

Omega Engineering OMR-6510 RS-422/RS-485, Repeapter, 115.2K bps, 2400 bps, 4800 bps, 9600 bps

Models: OMR-6510

1 39

Page 20

20		DATA- (G)					11
	DATA+		Tx+	Tx-	Rx+	Rx-	11
	DATA+		Tx+	Tx-	Rx+	Rx-

					RS-422/RS-485
			OMR-6510		Repeapter
					Repeapter
			Switch Position		Baud Rate
			SW1-1: ON		115.2K bps
			SW1-2: ON		2400 bps
			SW1-3: ON		4800 bps
			SW1-4: ON		9600 bps
			SW1-5: ON		19.2 K bps
			SW1-6: ON		38.4 K bps
1	(Y)DATA+	(G)DATA-	Tx+	Tx-	Rx+ RX-	(R)+Vs	(B)GND	10

3-2 OMR-6510

Page 20

Image 20

Omega Engineering OMR-6510 RS-422/RS-485, Repeapter, 115.2K bps, 2400 bps, 4800 bps, 9600 bps, Rx+ RX, SW1-1 ON, SW1-2 ON

Contents

M-3581 for User’s GuideContents 1.1 What is OMR ? 1.2 Outstanding Features of OMR∙ Two-wire and multi-drop communication ∙ Simple command / response protocol1-2 Introduction 1.3 OMR-6000 series products overview 1.4 EIA RS-485 StandardCommunication Module Analog Input Modules1.6 OMR RS-485 Network Configurations 1.5 RS-485 on OMRFigure 1-1 Simple Topology 1-4 IntroductionFigure 1-3 Free Topology 1.7 Constructing a OMR NetworkFigure 1-2 Branch Topology Terminator Connection 1.8 Termination Bus1.9. Shielding 1.10. How to Calculate Checksum Value Format of OMR Commands+ 0x32 MOD + 0x30 MODPage What is OMR-6520 ? Features of OMR-65202. OMR-6520 2.1. OverviewSpecifications of OMR-6520 ² Power² Input ² OutputA Look at OMR-6520 & Pin Assignment Pin Definitions Connection Between Host and OMR-6520OMR-6520 DATA + DATAFunctional Block Diagram 2.2. Setup Objective of SetupSetup Equipments Setup Procedure2.3. Installation SW2 SettingEquipments for Installation Installation Procedure2-8 OMR-6520 Figure 2-1 Application wiring of OMR-65202.4 Programming What is OMR-6510 ? Features of OMR-6510Specifications of OMR-6510 3. OMR-6510Switch Position RS-422/RS-485Repeapter 115.2K bpsPin Definitions OMR-6510OMR-6510 Functional Block Diagram 3-4 OMR-65103.2. Setup Objective of SetupSetup Equipments Setup Procedure3.3 Installation Equipments for InstallationInstallation Procedure Start BitFigure 3-1 OMR-6510 wiring 3.4 ProgrammingOMR-6510 Repeater +DATA DATA+ DATA DATAPage 4. Install a Brand New OMR Initialization Procedure AAs Baud rate is 9600 bps and check-sum is disable Initialization Procedure B6. Power on the power supply for OMR modules 8. Power of the local power supply 9. Disconnect the DEFAULT* pin10. Configure the OMR-6520 to desired Baud rate 11. Power on the local power supply4.2 Install a New OMR to a Existing Network Initialization WiringDATA+ DATA - Default Equipments for Install a New ModulePage 5.1 Software Installation 5.2 How to Execute the OMR AdministrationExecute the OMR Administration Utility 5. Software Utility5.3 OMR Administration Function Overview Default RS-232 Communication Port Setting5.3.1 Change RS-232 Communication Port Setting 96005.3.3 Using Operations 5-4 Software Utility Software Utility 5.3.4 Save and Print OMR modules’ information 5-6 Software UtilityVersion information 5.3.5 Version InformationHelp-About 5-8 Software Utility 6. Troubleshooting and Maintenance Using the LED IndicationProblem Preventive Maintain

RS-422/RS-485

OMR-6510

Repeapter

Switch Position

Baud Rate

SW1-1: ON

115.2K bps

SW1-2: ON

2400 bps

SW1-3: ON

4800 bps

SW1-4: ON

9600 bps

SW1-5: ON

19.2 K bps

SW1-6: ON

38.4 K bps

(Y)DATA+

(G)DATA-

Rx+ RX-

(R)+Vs

(B)GND