Omega Vehicle Security 850i operation manual Remote Sensor Bypass, Remote Engine Starting

REMOTE SENSOR BYPASS

To Activate Remote Sensor Bypass:

	U
Press & Release the “Arm/Lock” Button ( ) to Arm, then Press &
Release the “Auxiliary Output #2” Button ( II )
	THE SIREN WILL CHIRP TWICE TO
	CONFIRM ARMING
	THE SIREN THEN CHIRPS ONCE
	AGAIN TO CONFIRM SENSOR	THE PARKING LIGHTS
1st	BYPASS	WILL FLASH TWICE
	2nd	TO CONFIRM
		ARMING

		THE DOORS WILL LOCK
	2nd	UPON ARMING*
		Remote Sensor Bypass allows the option of
		turning off” the sensor any- time the system is
1st	armed using the transmitter or transceiver. When
	the sensor is bypassed, only the sensor zone is by-
	passed and all other protected zones will remain fully
	operational and vigilant. The sensor zone will reset to
	its normal operation the next time the system is armed.
* An optional doorlock interface must be installed

REMOTE ENGINE STARTING

The remote engine starting feature should not be used when

the vehicle is parked in an enclosed structure or garage!

Your Crime Guard 850i4e system offers the ultimate in comfort and convenience- remote engine starting. This feature allows the vehicle’s interior to be warmed in the winter or cooled in the summer before you enter the vehicle. Simply leave the climate controls set to the desired settings when leaving the vehicle prior to using the remote starting feature.

The following pages explain the remote engine starting operations. If the vehicle has a manual transmission, a special procedure is required when exiting the vehicle to enable the ability to remote start. Otherwise, the activation of remote start is the same for automatic or manual transmission vehicles.

Feature #2	30 or 60 Second Alarm Duration
	(Factory Default Setting 60 Seconds)

This feature allows the option of a 30 or 60 second Alarm Duration, which is when the system has activated in Armed state, sounding the siren and flashing the parking lights.

Changing the Alarm Duration:

Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and released twice. The system’s response will be two siren chirps, and the Status Light flashing two times, pausing, then repeating. Within 10 seconds, press and release the transmitter/transceiver’s "Arm/Lock" button to set the Alarm Dura- tion for 60 seconds (the siren will chirp once) or the "Disarm/Unlock" button to set the Alarm Duration for 30 seconds (the siren will chirp twice).

Feature #3	3 / 45 Second Arming Delay
	(Factory Default Setting 3 Second)

This feature determines how long after the Arming confirmation chirp that the system becomes fully Armed. The Arming Delay applies to the system Arming regardless if it occurs from using the transmitter/transceiver, Last Door Arming or Automatic Rearming.

Programming 3 / 45 Second Arming Delay:

Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and released three times. The system’s response will be three siren chirps, and the Status Light flashing three times, pausing, then repeating. Within 10 seconds, press and release the transmitter/transceiver’s "Disarm/Unlock" button to config- ure the system with a 45 second Arming Delay (the siren will chirp once) or the "Arm/Lock" button to configure the system with a 3 second Arming Delay (the siren will chirp twice).

Feature #4	Last Door Arming
	(Factory Default Setting Off)

This feature configures the system to automatically Arm itself 30 seconds after the vehicle’s last door is closed.

Programming Last Door Arming:

Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and released four times. The system’s response will be four siren chirps, and the Status Light flashing four times, pausing, then repeating. Within 10 seconds, press and release the transmitter/transceiver’s "Arm/Lock" button to turn on Last Door Arming (the siren will chirp once) or the "Disarm/Unlock" button to turn off Last Door Arming (the siren will chirp twice).

Page 18 Page 31