the Vehicle Recovery operation from the transmitter or transceiver in the event that you are forced from your car. “Remote Activated” Vehicle Recovery is one three methods of activating this feature, which is explained on page 27.
Programming Transmitter Activated Anti Car-Jacking:
Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and released sixteen times. The system’s response will be sixteen siren chirps, and the Status Light flashing sixteen times, pausing, then repeating. Within 10 seconds, press and release the transmitter/transceiver’s "Arm/Lock" button to turn on the Transmitter Activated Vehicle Recovery feature (the siren chirps once) or the "Disarm/Unlock" button to turn the feature off (the siren chirps twice).
Feature #17 | Chirp Confirmation |
| (Factory Default Setting On) |
This feature allows the permanent removal of the system’s chirping the siren as an audible confirmation when performing functions such as Arming and Disarming. Please note that utilizing this feature to remove the confirmation chirps does not affect siren chirping operations associated with the Unauthorized Transmitter Alert warning, sensor prewarning or Programming Mode.
Note: Using this feature to turn off the siren chirps also turns the chirps in the Echo transceiver- the Echo emulates the system’s siren chirps.
Programming the Chirp Confirmation:
Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and released seventeen times. The system’s response will be seventeen siren chirps, and the Status Light flashing seventeen times, pausing, then repeating. Within 10 seconds, press and release the transmitter/transceiver’s "Arm/Lock" button to turn the Chirp Confirmation on (the siren will chirp once) or the "Disarm/ Unlock" button to turn the Chirp Confirmation off (the siren will chirp twice).
Feature #18 Remote Start Run Time 10 Or 20 Minutes
(Factory Default Setting 10 Minutes)
This Feature sets the period of time that the engine will run after being remotely started. If the engine is not stopped by a transmitter or transceiver, or a safety circuit violation, the engine will automatically stop upon the expiration of the selected time period.
Programming 10 or 20 Minute Run Time:
Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and released eighteen times. The system’s response will be eighteen siren chirps, and the Status Light flashing eighteen times, pausing, then repeating. Within 10 seconds, press and release the transmitter/transceiver’s "Arm/Lock" button to
matic Rearming period. For example, if a vehicle door is opened during the 90 second period, the countdown will stop. When the door is closed, the system resets and starts a new 90 second countdown period.
•The Automatic Rearming sequence is indicated by a fast flashing Red Status Indicator Light, unless the system has been activated, in which case a Zone Violation Code will flash instead (pages
•If the system is disarmed while it is activated (siren sounding and lights flashing) Safety Disarm will cancel the Automatic Rearming for that disarming operation only. The next time the system is armed, Automatic Rearming will be initiated upon the subsequent disarming.
DISARMING BY EMERGENCY OVERRIDE
Emergency Override:
In the event that your transmitter is lost, damaged, or its batteries have become exhausted, the Valet Switch and the vehicle’s ignition key may be used to disarm the system. These Emergency Override instructions reflect a default setting of “1 press”; the “SecureCode” programmable feature allows the user to customize the number of Valet Switch presses needed for the Emergency Override. The SecureCode Emergency Override is described on the following page.
ENTER THE VEHICLE | WITHIN 5 SECONDS | ( |
( | ||
|
| ( |
AND USE YOUR KEY TO | OF TURNING THE | ECHO |
TURN THE IGNITION ON | IGNITION ON, PRESS | |
| AND RELEASE THE |
|
| VALET SWITCH |
|
| THE SYSTEM WILL DISARM |
To Disarm the System without using a Transmitter:
Step 1 With the system in the armed condition, enter the vehicle via the driver's door (be aware that the system will activate to an alarm condition when the door is opened).
Step 2 Using the ignition key, turn the vehicle’s ignition on.
Step 3 Within 5 seconds, press and release the Valet Switch once. The system will immediately disarm.
A procedure which separate, but similar, to an Emergency Override is the Alarm
Page 36 | Page 13 |