Onkyo Connecting a Turntable, Connecting a Preamp, Connecting the A-933-Continued

*En_A933_02.fm Page 15 Tuesday, January 25, 2005 1:46 PM

Connecting the A-933—Continued

Connecting a Turntable Connecting a Preamp

The A-933’s PHONO input jacks are for use with mov- ing-magnet (MM) type cartridges.

Use an analog audio cable to connect the A-933’s PHONO L/R jacks to the audio output jacks on the turn- table, as shown.

The A-933 can be used as a power amplifier with a sep- arate preamp.

In this case, use an analog audio cable to connect the A-933’s MAIN IN jacks to the preamp’s output jacks. Connect the speakers to the A-933, and connect the playback components to the preamp.

GND

L L

R R

PHONO (MM) TUNER

L L

SUBWOOFER

PREOUT

R	R
MAIN IN	OUT MD IN

L

R

PHONO (MM)

L

B	SPEAKERS	GND	L
	A		L
		L

R

LINE

CD

AC OUTLET

B

SPEAKERS

A

L

R

R

AC 230-240V

R

L

R

L

50 Hz

R

UNSWITCHED

LINE

TOTAL 100W MAX.

L

PHONO (MM)

TUNER

CD

L

L

L

R

L

R

L

R

REMOTE

SUBWOOFER

IN

PREOUT

OUT

CONTROL

CAUTION: SPEAKER IMPEDANCE

TAPE/CDR

R

INTEGRATED AMPLIFIER

A or B :

4 OHMS MIN. /SPEAKER

MODEL NOA. -933

A + B :

8 OHMS MIN. /SPEAKER

R

R

R

IN

IN

REMOTE

OUT

MD

OUT

CONTROL

MAIN IN

MAIN IN

TAPE/CDR

MODEL NOA. -933

INTEGRATED AMPLIFIER

AUDIO OUT

L

PRE OUT

R

L

R

Ground wire

Notes:

•If the turntable has a ground wire, connect it to A-933’s GND terminal. With some turntables, con- necting the ground wire may cause hum, in which case it should be disconnected.

•If the turntable has a moving-coil (MC) type car- tridge, you’ll need a commercially available MC phono preamp. In this case, connect the turntable to the phono preamp’s input, and connect the phono preamp’s output to the A-933’s PHONO L/R jacks.

Connecting a TV or Other Component with an Audio Output

Use an analog audio cable to connect the A-933’s LINE L/R jacks to the analog audio output jacks on the TV or other component, as shown.

			L					L
GND
L	L
					B	SPEAKERS		AR
R	R
			R	LINE
PHONO (MM)	TUNER		CD					AC OUTLET
L	L		L					LINE
								AC 230-240V
					R	L	R	L	50 Hz
SUBWOOFER								UNSWITCHED
								TOTAL 100W MAX.
PREOUT
R	R	IN	R	IN	REMOTE
OUT	MD		OUT		CONTROL			CAUTION: SPEAKER IMPEDANCE
MAIN IN			TAPE/CDR
						INTEGRATED AMPLIFIER		A or B :	4 OHMS MIN. /SPEAKER
						MODEL NOA. -933		A + B :	8 OHMS MIN. /SPEAKER

AUDIO OUT

L

R

Note:

If your TV has no audio output, you can connect the A-933 to an audio output on your VCR and use its tuner.

Notes:

•Do not connect a component that does not have an output volume control, because the sound will be out- put at maximum volume and may damage the A-933 and your speakers.

•To turn on the MAIN IN function, press the [MAIN IN] button for 3 seconds until the indicator lights up blue (page 19).

•When the A-933 is used as a power amplifier, the remote controller and the following functions are dis-

abled: Volume control, Muting, system functions, Tone/Direct function, subwoofer output, and Record- ing. Some of these functions can be performed on the connected preamp.

Connecting Another Component’s Power Cord

The A-933 has an AC OUTLET on its rear panel. This can be used to connect the power cord of another audio component that you intend to use with the A-933.

L

		B	SPEAKERS	A		AC OUTLET
						AC 230-240V
R						50 Hz
	LINE					UNSWITCHED
CD				AC OUTLET
L						TOTAL 100W MAX.
				AC 230-240V
		R	L R	L	50 Hz
				UNSWITCHED
				TOTAL 100W MAX.
R	IN	REMOTE
OUT		CONTROL		CAUTION: SPEAKER IMPEDANCE
TAPE/CDR
			INTEGRATED AMPLIFIER	A or B :	4 OHMS MIN. /SPEAKER
			MODEL NOA. -933	A + B :	8 OHMS MIN. /SPEAKER

Caution:

•Make sure that the maximum power requirement of the component connected to the AC OUTLET does not exceed the capacity printed on the A-933’s rear

panel (100W).

15