Enjoying music or videos with the TX-DS696
Jog dial
DISPLAY |
|
| DIMMER |
|
|
|
| CH LEVEL |
| |||||
|
|
|
|
|
|
|
|
| REC OUT |
| ZONE 2 ZONE 2 LEVEL | CH LEVEL | MASTER VOLUME |
|
STANDBY/ON |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| DSP/MODE ADJ | SETUP |
|
|
STANDBY |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| RETURN |
|
|
POWER |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| PUSH TO ENTER |
|
|
|
ON | OFF |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| DISPLAY | DIMMER | FM MODE | PRESET MEMORY | TUNING |
| PRESET |
| SMART SCAN NAVIGATOR |
|
| |
|
|
|
|
|
|
|
|
|
|
|
| BASS | TREBLE | |
PHONES | AUDIO | DVD | VIDEO 1 | VIDEO 2 | VIDEO 3 | VIDEO 4 | TAPE | FM | AM | PHONO | C D |
|
| |
|
| SELECTOR |
|
| ||||||||||
|
|
|
| VCR 1 | VCR 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| AV RECEIVER | |
Switching the display
While listening to or watching an input source, you can display the information regarding the type of source and signal being input by pressing the DISPLAY button on the
Remote controller | |||||
| DISPLAY |
|
|
| |
|
|
|
|
|
|
When an input source other than FM or AM is selected:
Input + volume
Program format*
Input + Listening mode or Multi Ch
*If the input signal does not have a program format, then this will be skipped.
When FM or AM is selected as the input source:
FM/AM frequency +
ch
Preset no.
FM/AM +
Listening mode
Adjusting the brightness of the front display
You can adjust the brightness of the front display of the
Remote controller |
(Other than European models)
DIMMER
SLEEP 
CH SEL 
LEVEL 
DISPLAY 
DIMMER
HOME THEATER CONTROLLER
Using the sleep time (remote controller only)
The SLEEP button enables you to set the
If you are using the remote zone (Zone 2), it will turn off at the same time as the main zone. If you want to set the sleep function for Zone 2 only, set the sleep function with main zone turned on and then put the main zone into the standby state.
Temporarily changing the speaker output levels
To change the individual speaker volumes temporarily, follow the procedure given below. Each channel can be set between
CH LEVEL
1. Press the CH LEVEL button and select the desired speaker.
DSP/MODE ADJ
2.Turn the jog dial to adjust the volume level.
PUSH TO ENTER
When using the remote controller:
1. Press the RCVR MODE button.
2. Press the CH SEL button and select the desired speaker.
3. Press the LEVEL 
or 
button to adjust the volume level.
Notes:
•You cannot select a speaker if the Speaker Config
•If the speaker level is set to +1 dB or higher, the maximum level indicated on the display will change if you raise the volume level.
•When you press the TEST button after you set the level, the current level will be used as the value set via the test tone.
30
