Connecting the power

SEND/LEARN indicator

 

 

 

 

 

 

 

 

 

 

 

ON

 

 

STNBY

STANDBY indicator

 

 

 

 

 

 

 

 

 

AUDIO MODE

 

 

 

STANDBY/ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUDIO

 

 

MUTING

 

 

PTY/TP

 

FM MUTE /

 

 

CHARACTER /

BASS /

 

MASTER VOLUME

TRACK

DISC

 

 

 

MODE

DOWN TUNING

UP

MEMORY

TREBLE

CH LEVEL

ZONE 2 VOL

 

 

 

 

STANDBY/ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DSP/PRESET

 

 

 

 

 

STANDBY

ZONE 2

 

 

 

 

 

 

 

 

 

REC

 

 

OPEN/CLOSE

 

 

 

 

 

SMART SCAN

 

 

 

 

 

 

 

 

 

 

 

 

 

CONTROLLER

 

 

 

 

 

 

POWER

 

 

 

 

 

 

 

 

 

 

 

 

 

ON

OFF

 

 

 

 

 

 

 

PUSH TO ENTER

DVD

 

 

CD

REC OUT

ZONE 2

 

 

LISTENING MODE

 

 

 

 

 

 

 

 

 

DISPLAY

DIRECT

STEREO

/DTSTHX

 

MENU

 

 

EXIT

T1

T2

TUN

PH

 

 

 

 

SURROUND

 

 

 

 

 

V1

V2

V3

V–

 

 

 

 

 

 

 

 

 

 

 

STEREO

 

DIRECT

DSP

PHONES

AUDIO SELECTOR

 

 

 

 

 

 

 

VIDEO 4 /VIDEO CAM INPUT

1

 

2

3

 

 

DVD VIDEO 1

VIDEO 2 VIDEO 3

VIDEO 4

TAPE

FM

AM

 

PHONO

C D

SURROUND

 

THX

DSP

 

 

 

4

 

5

6

 

 

VCR 1

VCR 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S VIDEO VIDEO L AUDIO R

Re-EQ

 

CH SEL

LEVEL +

 

 

 

 

 

 

 

 

 

 

AV RECEIVER TX-DS787

7

 

8

9

 

 

 

 

 

 

 

 

 

 

LATE NIGHT DIMMER

LEVEL –

 

 

 

 

 

 

 

 

 

 

 

+ 10

 

0

ENT

 

 

 

 

 

 

 

 

 

 

 

HOME THEATER CONTROLLER

 

 

 

 

 

 

 

 

 

 

 

 

RC-390M

 

POWER

 

 

 

To wall outlet

 

 

 

 

 

 

Connecting the power

•The TX-DS787 is shipped with the main power (POWER) switch in the on position ( ON). When the power cord is plugged in for the first time, the TX-DS787 will automatically enter the standby state and the STANDBY indicator will light (same condition after step 2 below).

•Before you plug in the TX-DS787, confirm that all connections have been made properly.

•Turning on the power may cause a momentary power surge, which might interfere with other electrical equipment on the same circuit, such as computers. If this happens, use a wall outlet on a different circuit.

1.Plug the power cord into an AC wall outlet.

2.Press the POWER switch to set the TX-DS787 to standby state.

The STANDBY indicator will light up.

3.Press the STANDBY/ON button to turn on the TX-DS787. The display will light up and the STANDBY indicator will turn off.

If you press the STANDBY/ON button again, the receiver returns to Standby mode.

Turning the power on from the remote controller:

Before you can use the remote controller, you must perform steps 1 and 2 above and place the TX-DS787 in the standby state.

1.Press the AUDIO MODE button.

2.Press the ON button to turn on the TX-DS787 (take it out of the standby state).

•To return the TX-DS787 to the standby state, press the STNBY button.

Memory preservation

This unit does not require memory preservation batteries. A built-in memory power backup system preserves the contents of the memory during power failures and even when the POWER switch is set to off. The POWER switch must be set to on in order to charge the backup system.

The memory preservation period after the unit has been turned off varies depending on climate and placement of the unit. On the average, memory contents are protected over a period of a few weeks after the last time the unit has been turned off. This period is shorter when the unit is exposed to a highly humid climate.

27