Enjoying music or videos in the remote zone

 

 

 

 

POWER

 

 

 

 

 

 

 

 

ON

 

 

 

 

 

 

 

 

 

 

 

 

VOL

 

 

 

 

AUDIO

 

 

MUTING

 

 

 

 

 

MASTER VOLUME

TRACK

DISC

 

STANDBY/ON

 

 

 

 

 

 

 

 

STANDBY

 

 

 

 

 

 

 

 

 

 

 

 

REC

 

OPEN/CLOSE

 

 

 

 

 

DVD

 

 

CD

 

 

ZONE 2 (GRN )

 

 

 

 

 

 

Input

DISPLAY

REC ( RED )

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5

TAPE 1TAPE 2AMFMPHONOC D

OPEN/CLOSE

 

 

 

DVD

 

 

PH

 

POWER

 

 

 

T1

T2

TUN

selector

 

 

 

 

STEREO

DIRECT

DSP

ON OFF

 

 

 

V1

V2

V3

V–

 

 

 

 

 

 

 

 

buttons

 

 

 

 

SURROUND

THX

DSP

 

 

 

 

 

1

2

3

 

 

 

 

CLEAR

PHONES

4

5

6

 

 

 

 

 

Re-EQ

CH SEL

LEVEL +

 

 

 

 

 

 

7

8

9

 

 

 

 

 

LATE NIGHT DIMMER

LEVEL –

 

 

 

 

 

+ 10

0

ENT

 

 

 

 

 

AV RECEIVER TX-DS989

HOME THEATER CONTROLLER

 

 

 

 

 

 

 

 

 

 

 

 

RC-390M

 

 

Zone 2

Off

 

 

 

 

 

 

Controlling the TX-DS989 from the remote zone

1.Aiming at the remote sensor, press the POWER ON button on the remote controller.

Note:

Controlling the TX-DS989 without the remote controller

1.Press the Zone 2 button on the TX-DS989.

2.Select a source.

Be aware that if you start using the system in the remote zone (Zone 2) while a recording is going on in the main zone, the recording is aborted.

2.Press the appropriate input selector button on the remote controller to select the desired source.

After pressing the Zone 2 button, you must press an input source button within 8 seconds. To select the same source as that selected for the main zone, press the Zone 2 button twice in succession. The indicator above the selected input source will light green. Adjust the volume in the remote zone as desired.

Ex.: When the Zone 2 button is pressed twice

3. Adjust the volume on the power amplifier to the desired level.

Ex.: When the Zone 2 button and then VIDEO 4 button are pressed

Notes:

• If the Zone 2 button was pressed twice so that the same source is being played in the main and remote zones, then changing the input source in the main zone also changes the input source for the remote zone.

• In the remote zone, you can only play the source in the 2- channel mode. You cannot play the source in the remote zone in the surround mode.

• If the Rec Out button is pressed in the main room while someone is using the system in the remote zone, the Zone 2 function will be deactivated and the source will turn off in the remote zone.

• The Zone 2 terminal is an analog output. Digital signals are not output. If no sound is heard from the selected input source, check if the component is connected to the analog inputs.

• Please note that some third-party multi-room system components may not be fully compatible with the Onkyo multi-room system components.

• If you are not using the system in the remote zone, always press the Zone 2 button and then the Off button to turn the 49

Zone 2 function off.