Onkyo TX-NR616 instruction manual En-83, USB Device Playback, Others

USB Device Playback

■Can’t access the music files on a USB device

Make sure the USB device is plugged in properly.	—
The AV receiver supports USB devices that support	96
the USB mass storage device class. However,
playback may not be possible with some USB devices
even if they conform to the USB mass storage device
class.

USB memory devices with security functions cannot — be played.

Others

■Standby power consumption

In the following cases, the power consumption in 65, 66,

standby mode may reach up to a maximum of 8.3 W: 68

–The “HDMI Control(RIHD)” setting is set to “On”. (Depending on the TV status, the AV receiver will enter standby mode as usual.)

–The “HDMI Through” setting is set to other than “Off”.

–The “Network Standby” setting is set to “On”.

If an MHL-enabled mobile device is connected to the 16 AUX (front) input, the power consumption in standby mode will increase.

■The sound changes when I connect my headphones

When a pair of headphones is connected, the listening — mode is set to Stereo, unless it’s already set to Stereo, Mono, Direct, or Pure Audio (European, Australian and Asian models).

■The speaker distance cannot be set as required

The values entered may be automatically adjusted	—
with values best-suited for your home theater.

■ The display doesn’t work

The display is turned off when the Pure Audio	—
(European, Australian and Asian models) listening
mode is selected.

■How do I change the language of a multiplex source

Use the “Multiplex” setting in the “Audio Adjust” 57 menu to select “Main” or “Sub”.

■ The ufunctions don’t work

To use u, you must make an uconnection and an	18
analog audio connection (RCA) between the
component and AV receiver, even if they are
connected digitally.
While Zone 2/3 is selected, the ufunctions don’t	18
work.

■The functions System On/Auto Power On and Direct Change don’t work for components connected via u

These functions don’t work when Zone 2/3 is turned 18 on.

■When performing “Automatic Speaker Setup”, the measurement fails and the message “Ambient noise is too high.” is displayed.

This can be caused by a malfunction in your speaker — unit. Check if the unit produces normal sounds.

■The following settings can be made for the composite video inputs

You must use the buttons on the unit to make these settings.

On the AV receiver, press the input selector for the input source that you want to set and the SETUP button simultaneously. While holding down the input selector button, press SETUP until “Video ATT :On” appears on the AV receiver’s display. Then, release both buttons.

En-83

Appendix

To turn the setting off, repeat the above process so that “Video ATT :Off” appears on the AV receiver’s display, and release the buttons.

• Video Attenuation

This setting can be made for the BD/DVD, CBL/SAT, STB/DVR, GAME or USB input.

If you have a game console connected to the composite video input, and the picture isn’t very clear, you can attenuate the gain.

Video ATT :Off: (default).

Video ATT :On: Gain is reduced by 2 dB.

■If the picture on your TV/monitor connected to the HDMI output(s) is unstable, try switching the DeepColor function off

To turn off the DeepColor function, simultaneously press the STB/DVR and 8ON/STANDBY buttons on the AV receiver. While holding down STB/DVR, press 8ON/STANDBY until “Deep Color:Off” appears on the AV receiver’s display. Then, release both buttons. To reactivate the DeepColor function, repeat the above process until “Deep Color:On” appears on the AV receiver’s display and release the buttons.

The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in.

Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s malfunction. Before you record important data, make sure that the material will be recorded correctly.

Before disconnecting the power cord from the wall outlet, set the AV receiver to standby.